✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-EAR-2281

Lapse Rate from Two Pressure Levels

The lapse rate describes the change in atmospheric temperature with vertical distance. When temperature and pressure are known at two atmospheric pressure levels, the hypsometric equation can estimate the height difference, allowing the average temperature lapse rate between those levels to be calculated.

\(\Gamma = (T_{1} - T_{2})/\Delta z, \text{ where } \Delta z = (R_{\mathrm{d}} \bar{T}_{v}/g) \ln(p_{1}/p_{2})\)

What this formula means

The lapse rate describes the change in atmospheric temperature with vertical distance. When temperature and pressure are known at two atmospheric pressure levels, the hypsometric equation can estimate the height difference, allowing the average temperature lapse rate between those levels to be calculated.

Scientific principle

Principle

Atmospheric pressure decreases with altitude because of the weight of the air above a given level. The hydrostatic equation and ideal gas law combine to produce the hypsometric equation, which relates pressure differences to atmospheric layer thickness.

Derivation

  • 1. Define the average lapse rate between two atmospheric levels as Γ = (T₁ − T₂)/Δz.

  • 2. The hydrostatic equation is dp/dz = −ρg.

  • 3. Using the ideal gas relation for moist air in virtual-temperature form gives ρ = p/(R_d Tᵥ).

  • 4. Substitute density into the hydrostatic equation and integrate between pressure levels p₁ and p₂.

  • 5. The hypsometric equation gives Δz = (R_d T̄ᵥ/g) ln(p₁/p₂).

  • 6. Substitute this height difference into the lapse-rate definition.

  • 7. The resulting average lapse rate is Γ = (T₁ − T₂)g/[R_d T̄ᵥ ln(p₁/p₂)].

Final Result

Γ = (T₁ − T₂)g/[R_d T̄ᵥ ln(p₁/p₂)]

Interpretation

A positive lapse rate indicates that temperature decreases with height between the two levels. A negative value indicates that temperature increases with height, corresponding to an average inversion.

Variables and their meanings

SymbolMeaningUnit

Γ

Average atmospheric temperature lapse rate

K/m or K/km

T₁, T₂

Air temperatures at the lower and upper pressure levels

K

Δz

Vertical distance between the two pressure levels

m

p₁, p₂

Atmospheric pressures at the lower and upper levels, respectively

Pa

R_d

Specific gas constant for dry air, approximately 287.05

J/(kg·K)

T̄ᵥ

Layer-mean virtual temperature

K

g

Gravitational acceleration

m/s²

SI units and conversions

Lapse Rate

K/m or K/km

Temperature

K

Pressure

Pa

Height

m

Specific Gas Constant

J/(kg·K)

Gravitational Acceleration

m/s²

Conditions of use

  • The lower pressure level must have greater pressure than the upper level.

  • Temperatures must be expressed in kelvin when used in the hypsometric equation.

  • Pressure values must use the same units.

  • The layer-mean virtual temperature should represent the atmospheric layer.

  • The calculated lapse rate is an average over the layer, not necessarily the local lapse rate at every altitude.

Limitations and assumptions

  • The hypsometric equation assumes hydrostatic balance.

  • Using a single arithmetic mean temperature is an approximation when temperature varies strongly with height.

  • Moisture affects air density, so virtual temperature is preferable to ordinary temperature for accurate calculations.

  • The result does not describe small-scale temperature inversions within the layer.

  • A two-level calculation cannot determine the complete vertical temperature profile.

Step-by-step worked examples

ProblemSolutionAnswer

At a lower pressure level of 1,000 hPa, the air temperature is 290 K. At an upper level of 800 hPa, the temperature is 278 K. If the mean virtual temperature is 284 K, calculate the average lapse rate using g = 9.81 m/s².

  • Given: p₁ = 1,000 hPa and p₂ = 800 hPa.

  • T₁ = 290 K and T₂ = 278 K.

  • T̄ᵥ = 284 K.

  • First calculate the height difference:

  • Δz = (287.05 × 284/9.81) ln(1000/800).

  • Δz ≈ 1,701 m.

  • Temperature difference = 290 − 278 = 12 K.

  • Γ = 12/1,701.

  • Γ ≈ 0.00705 K/m = 7.05 K/km.

The average lapse rate is approximately 7.05 K/km.

An atmospheric layer has p₁ = 900 hPa, p₂ = 700 hPa, T₁ = 285 K, T₂ = 270 K, and mean virtual temperature 277.5 K. Calculate the average lapse rate.

  • Given: p₁ = 900 hPa and p₂ = 700 hPa.

  • T₁ = 285 K and T₂ = 270 K.

  • T̄ᵥ = 277.5 K.

  • Δz = (287.05 × 277.5/9.81) ln(900/700).

  • Δz ≈ 2,046 m.

  • Γ = (285 − 270)/2,046.

  • Γ ≈ 0.00733 K/m.

  • Γ ≈ 7.33 K/km.

The average lapse rate is approximately 7.33 K/km.

Real-world applications

  • Atmospheric sounding analysis

  • Weather forecasting

  • Atmospheric stability assessment

  • Temperature profile reconstruction

  • Climate and boundary-layer research

  • Meteorological interpretation of radiosonde observations

Formula Meaning

The lapse rate describes the change in atmospheric temperature with vertical distance. When temperature and pressure are known at two atmospheric pressure levels, the hypsometric equation can estimate the height difference, allowing the average temperature lapse rate between those levels to be calculated.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source