✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1513

Complex Power Relation

Complex power combines real power and reactive power into one complex quantity. It is calculated using the RMS voltage phasor multiplied by the complex conjugate of the RMS current phasor.

\(\tilde{S} = P + jQ = \tilde{V}\tilde{I}*\)

What this formula means

Complex power combines real power and reactive power into one complex quantity. It is calculated using the RMS voltage phasor multiplied by the complex conjugate of the RMS current phasor.

Scientific principle

Principle

Complex power represents the combined real and reactive power behavior of a sinusoidal AC circuit. Its real component describes average energy transfer, while its imaginary component describes reactive energy exchange.

Derivation

  • Represent RMS voltage and current using phasors: Ṽ = V∠θᵥ and Ĩ = I∠θᵢ.

  • The complex conjugate of current is Ĩ* = I∠(−θᵢ).

  • Multiply voltage by the current conjugate: S̃ = ṼĨ*.

  • Therefore, S̃ = VI∠(θᵥ − θᵢ).

  • Let φ = θᵥ − θᵢ.

  • Using Euler's identity, S̃ = VI(cos φ + j sin φ).

  • The real component is P = VI cos φ, and the imaginary component is Q = VI sin φ.

  • Thus, S̃ = P + jQ.

Final Result

S̃ = ṼĨ* = P + jQ.

Variables and their meanings

S̃

Complex power.

P

Real power.

Q

Reactive power.

Ṽ

Complex RMS voltage phasor.

Ĩ

Complex RMS current phasor.

Ĩ*

Complex conjugate of the RMS current phasor.

J

Imaginary unit, where j² = −1.

Φ

Voltage-current phase difference.

SI units and conversions

S̃

VA, with real and imaginary components expressed in W and var.

P

W.

Q

var.

Ṽ

V.

Ĩ

A.

Φ

rad or degrees.

Conditions of use

  • Use RMS phasors rather than peak-amplitude phasors.

  • Voltage and current must have the same frequency.

  • The circuit should be in sinusoidal steady state.

  • The passive sign convention should be applied consistently when interpreting positive and negative power.

Limitations and assumptions

  • The simple complex-power representation assumes sinusoidal steady-state operation.

  • Nonsinusoidal waveforms can require additional distortion-power analysis.

  • Using Ĩ instead of Ĩ* gives an incorrect phase relationship under the usual convention.

  • Complex power is not itself a measure of energy; energy requires integration of power over time.

Step-by-step worked examples

ProblemSolutionAnswer

An AC circuit has RMS voltage phasor Ṽ = 100∠0° V and RMS current phasor Ĩ = 5∠−36.87° A. Calculate complex power.

  • S̃ = ṼĨ*.

  • Ĩ* = 5∠36.87° A.

  • S̃ = 100∠0° × 5∠36.87°.

  • S̃ = 500∠36.87° VA.

  • P = 500 cos 36.87° = 400 W.

  • Q = 500 sin 36.87° = 300 var.

S̃ = 400 + j300 VA.

A sinusoidal AC circuit has real power 240 W and reactive power −180 var. Calculate complex power magnitude and phase angle.

  • S̃ = P + jQ.

  • S̃ = 240 − j180 VA.

  • |S̃| = √(240² + 180²).

  • |S̃| = √90000 = 300 VA.

  • φ = tan⁻¹(Q/P) = tan⁻¹(−180/240).

  • φ ≈ −36.87°.

S̃ = 240 − j180 VA, with magnitude 300 VA and phase angle approximately −36.87°.

Real-world applications

  • AC power-flow analysis.

  • Electrical network simulation.

  • Power-factor correction calculations.

  • Analyzing inductive and capacitive loads.

  • Determining real and reactive power in electrical systems.

Formula Meaning

Complex power combines real power and reactive power into one complex quantity. It is calculated using the RMS voltage phasor multiplied by the complex conjugate of the RMS current phasor.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source