✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1524

BJT Emitter Current

The emitter current of a bipolar junction transistor is equal to the sum of its collector current and base current, following the conventional current-direction definition.

\(I_{\mathrm{E}} = I_{\mathrm{C}} + I_{\mathrm{B}}\)

What this formula means

The emitter current of a bipolar junction transistor is equal to the sum of its collector current and base current, following the conventional current-direction definition.

Scientific principle

Principle

The three terminal currents of a BJT are related by conservation of electric charge. The emitter current supplies the current that flows through the collector and base terminals.

Derivation

  • 1. A BJT has three terminal currents: emitter current I_E, collector current I_C, and base current I_B.

  • 2. Kirchhoff’s Current Law states that the algebraic sum of currents at a node is zero.

  • 3. With conventional current magnitudes defined for normal transistor operation, the emitter current equals the sum of the other two terminal currents.

  • 4. Therefore, I_E = I_C + I_B.

  • 5. Using β = I_C/I_B, the emitter current can also be written as I_E = (β + 1)I_B.

Final Result

I_E = I_C + I_B = (β + 1)I_B

Alternative Relation

I_E = I_C/α

Variables and their meanings

SymbolMeaningUnit

I_E

Emitter current

A

I_C

Collector current

A

I_B

Base current

A

β

Common-emitter current gain

Dimensionless

α

Common-base current gain

Dimensionless

SI units and conversions

Current

A

Current Gain

Dimensionless

Dimensional Formula

Current: [I]; current gains: dimensionless

Conditions of use

  • The currents must use a consistent reference-direction convention.

  • The equation applies to NPN and PNP transistors when terminal-current directions are interpreted consistently.

  • For ordinary forward-active operation, the equation can be used with positive current magnitudes.

  • The relation follows from charge conservation and is not restricted to the forward-active region.

Limitations and assumptions

  • The signs of terminal currents depend on the chosen reference directions and transistor polarity.

  • The equation does not independently determine the operating point; the external circuit is also required.

  • Leakage currents may affect measured terminal-current values, although charge conservation still applies.

  • The relation I_E = (β + 1)I_B depends on using the corresponding definition of β.

Step-by-step worked examples

ProblemSolutionAnswer

A BJT has a collector current of 8 mA and a base current of 80 μA. Calculate the emitter current.

  • Given: I_C = 8 mA and I_B = 80 μA = 0.08 mA.

  • Use: I_E = I_C + I_B.

  • I_E = 8 + 0.08.

  • I_E = 8.08 mA.

The emitter current is 8.08 mA.

A transistor has β = 99 and a base current of 20 μA. Determine its emitter current.

  • Use: I_E = (β + 1)I_B.

  • I_E = (99 + 1) × 20 μA.

  • I_E = 100 × 20 μA.

  • I_E = 2000 μA = 2 mA.

The emitter current is 2 mA.

Real-world applications

  • BJT current analysis

  • Emitter-resistor bias circuits

  • Common-base amplifier calculations

  • Transistor current measurement

  • Current-conservation verification

Formula Meaning

The emitter current of a bipolar junction transistor is equal to the sum of its collector current and base current, following the conventional current-direction definition.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source