MOSFET transconductance measures the change in drain current produced by a small change in gate-source voltage at a specified operating point. The stated expression applies to the ideal long-channel saturation-region square-law model.
MOSFET Transconductance
MOSFET transconductance measures the change in drain current produced by a small change in gate-source voltage at a specified operating point. The stated expression applies to the ideal long-channel saturation-region square-law model.
\(g_{\mathrm{m}} = \mu_{\mathrm{n}} C_{\mathrm{ox}} (W/L)V_{\mathrm{OV}} = 2I_{\mathrm{D}}/V_{\mathrm{OV}}\)
What this formula means
Scientific principle
Principle
In saturation, the ideal long-channel MOSFET drain current is proportional to the square of gate overdrive voltage. Differentiating drain current with respect to gate-source voltage gives transconductance.
Derivation
1. The ideal saturation current is I_D = ½μ_nC_ox(W/L)V_OV².
2. Gate overdrive is V_OV = V_GS − V_TH.
3. Transconductance is defined as g_m = ∂I_D/∂V_GS at a fixed operating point.
4. Differentiating the square-law expression gives g_m = μ_nC_ox(W/L)V_OV.
5. From the drain-current equation, μ_nC_ox(W/L)V_OV = 2I_D/V_OV.
6. Therefore, g_m = μ_nC_ox(W/L)V_OV = 2I_D/V_OV.
Final Result
g_m = μ_n C_ox (W/L)V_OV = 2I_D/V_OV
Alternative Relation
g_m = √[2μ_nC_ox(W/L)I_D]
Model Note
These equivalent expressions assume ideal long-channel saturation operation without significant channel-length modulation.
Variables and their meanings
| Symbol | Meaning | Unit |
|---|---|---|
g_m | Small-signal MOSFET transconductance | S or A/V |
μ_n | Electron mobility | m²/(V·s) |
C_ox | Gate-oxide capacitance per unit area | F/m² |
W | Channel width | m |
L | Channel length | m |
V_OV | Gate overdrive voltage, V_GS − V_TH | V |
I_D | DC drain operating current | A |
V_GS | Gate-to-source voltage | V |
V_TH | Threshold voltage | V |
SI units and conversions
Transconductance
S = A/V
Drain Current
A
Overdrive Voltage
V
Dimensional Formula
Transconductance: [M⁻¹ L⁻² T³ I²]
Conditions of use
The MOSFET should be operating in the saturation region.
The gate overdrive voltage must be positive.
The long-channel square-law approximation should be reasonably valid.
The result represents small-signal behaviour around a DC operating point.
The small-signal gate-voltage variation should be sufficiently small for linearization.
Limitations and assumptions
The equation assumes a long-channel MOSFET with approximately constant mobility.
Short-channel effects and velocity saturation can change the transconductance relationship.
Mobility degradation and series resistance can reduce practical transconductance.
Channel-length modulation is neglected in the ideal derivation.
In the triode region, the saturation-region expression must not be used without modification.
Step-by-step worked examples
| Problem | Solution | Answer |
|---|---|---|
A MOSFET operates in ideal saturation with I_D = 2 mA and V_OV = 0.5 V. Calculate its transconductance. |
| The transconductance is 8 mS. |
A long-channel MOSFET has μ_nC_ox(W/L) = 4 mA/V² and V_OV = 0.75 V. Determine its transconductance. |
| The transconductance is 3 mS. |
Real-world applications
Common-source amplifier design
MOSFET small-signal modelling
CMOS analog circuit design
Differential-pair analysis
Amplifier gain estimation
Formula Meaning
MOSFET transconductance measures the change in drain current produced by a small change in gate-source voltage at a specified operating point. The stated expression applies to the ideal long-channel saturation-region square-law model.
Sources and further reading
No source has been supplied for this item yet. Treat the claim as needing editorial verification.