✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1530

JFET Drain Current (Shockley Model)

The Shockley JFET equation estimates drain current as a function of gate-source voltage for a junction field-effect transistor operating in its normal pinch-off or saturation region.

\(I_{\mathrm{D}} = I_{\mathrm{DSS}}(1 - V_{\mathrm{GS}}/V_{\mathrm{P}})^{2}\)

What this formula means

The Shockley JFET equation estimates drain current as a function of gate-source voltage for a junction field-effect transistor operating in its normal pinch-off or saturation region.

Scientific principle

Principle

A JFET controls channel conductivity through the electric field produced by its reverse-biased gate-channel junction. Increasing reverse gate bias widens the depletion regions, narrows the conducting channel, and reduces drain current.

Derivation

  • 1. I_DSS is the drain current at V_GS = 0 under the specified saturation-region conditions.

  • 2. V_P is the gate-source voltage at channel cutoff using the Shockley-model sign convention.

  • 3. The idealized channel-current model assumes that the drain current varies approximately with the square of the normalized remaining channel-control factor.

  • 4. The normalized factor is 1 − V_GS/V_P.

  • 5. Squaring this factor and multiplying by I_DSS gives I_D = I_DSS(1 − V_GS/V_P)².

  • 6. For an n-channel JFET, V_P is normally negative, and the equation is used over the range V_P ≤ V_GS ≤ 0.

Final Result

I_D = I_DSS(1 − V_GS/V_P)²

Special Cases

  • At V_GS = 0: I_D = I_DSS.

  • At V_GS = V_P: I_D = 0 in the ideal Shockley model.

  • At intermediate reverse gate bias: drain current lies between zero and I_DSS in the model.

Variables and their meanings

SymbolMeaningUnit

I_D

JFET drain current

A

I_DSS

Drain-to-source saturation current at zero gate-source voltage

A

V_GS

Gate-to-source voltage

V

V_P

Gate-source cutoff or pinch-off voltage in the Shockley-model convention

V

SI units and conversions

Drain Current

A

Voltage

V

Ratio

Dimensionless

Dimensional Formula

Drain current: [I]; voltage: [M L² T⁻³ I⁻¹]

Conditions of use

  • The equation is used for a JFET in its normal drain-current saturation region.

  • For an n-channel JFET, V_P is negative and V_GS normally ranges from V_P to 0.

  • The gate-channel junction should remain reverse-biased during normal operation.

  • I_DSS and V_P should correspond to the specific JFET and operating conditions.

  • The equation assumes the ideal Shockley square-law model.

Limitations and assumptions

  • The Shockley equation is an approximate model and does not capture every feature of a real JFET.

  • Device parameters vary with manufacturing tolerances and temperature.

  • The equation is not intended to model the ohmic region at small drain-source voltage.

  • Gate leakage and breakdown effects are neglected.

  • For a p-channel JFET, voltage and current signs must be interpreted using the appropriate polarity convention.

Step-by-step worked examples

ProblemSolutionAnswer

An n-channel JFET has I_DSS = 12 mA, V_P = −6 V, and V_GS = −2 V. Calculate its drain current using the Shockley model.

  • Given: I_DSS = 12 mA, V_P = −6 V, V_GS = −2 V.

  • Use: I_D = I_DSS(1 − V_GS/V_P)².

  • I_D = 12(1 − (−2)/(−6))² mA.

  • I_D = 12(1 − 1/3)² mA.

  • I_D = 12(2/3)² mA.

  • I_D = 12 × 4/9 mA.

  • I_D ≈ 5.33 mA.

The drain current is approximately 5.33 mA.

A JFET has I_DSS = 8 mA and cutoff voltage V_P = −4 V. Find the ideal drain current when V_GS = −1 V.

  • Given: I_DSS = 8 mA, V_P = −4 V, V_GS = −1 V.

  • I_D = 8(1 − (−1)/(−4))² mA.

  • I_D = 8(1 − 0.25)² mA.

  • I_D = 8 × 0.75² mA.

  • I_D = 8 × 0.5625 mA.

  • I_D = 4.5 mA.

The drain current is 4.5 mA.

Real-world applications

  • JFET bias-circuit analysis

  • Low-noise amplifier design

  • Analog signal-conditioning circuits

  • JFET current-source calculations

  • Semiconductor device characterization

Formula Meaning

The Shockley JFET equation estimates drain current as a function of gate-source voltage for a junction field-effect transistor operating in its normal pinch-off or saturation region.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source