✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1534

Solar Cell Efficiency

Solar-cell efficiency is the percentage of incident optical power converted into useful electrical output power. The maximum-power expression uses the cell's maximum-power point, while the fill-factor form relates efficiency to open-circuit voltage and short-circuit current.

\(\eta = (P_{\mathrm{max}}/P_{\mathrm{in}}) \times 100\% = (V_{\mathrm{oc}} I_{\mathrm{sc}} FF/P_{\mathrm{in}}) \times 100\%\)

What this formula means

Solar-cell efficiency is the percentage of incident optical power converted into useful electrical output power. The maximum-power expression uses the cell's maximum-power point, while the fill-factor form relates efficiency to open-circuit voltage and short-circuit current.

Scientific principle

Principle

A photovoltaic cell converts part of the incident solar radiation into electrical energy through the photovoltaic effect. Efficiency compares the maximum electrical power delivered by the cell with the optical power incident on its active area.

Derivation

  • 1. Electrical output power at any operating point is P = VI.

  • 2. At the maximum-power point, P_max = V_mp I_mp.

  • 3. Incident optical power is P_in = G A, where G is irradiance and A is the illuminated active area.

  • 4. Efficiency is defined as the ratio of maximum output power to incident optical power.

  • 5. Therefore, η = P_max/P_in.

  • 6. Using FF = P_max/(V_oc I_sc), substitute P_max = V_oc I_sc FF.

  • 7. Thus, η = V_oc I_sc FF/P_in.

  • 8. Multiplying by 100 converts the dimensionless ratio into a percentage.

Final Result

η = (V_mp I_mp/P_in) × 100% = (V_oc I_sc FF/P_in) × 100%

Incident Power Relation

P_in = GA

Variables and their meanings

SymbolMeaningUnit

η

Solar-cell energy-conversion efficiency

Dimensionless or %

P_max

Maximum electrical output power

W

P_in

Incident optical power

W

V_mp

Voltage at maximum-power point

V

I_mp

Current at maximum-power point

A

V_oc

Open-circuit voltage

V

I_sc

Short-circuit current

A

FF

Solar-cell fill factor

Dimensionless

G

Incident irradiance

W/m²

A

Illuminated active cell area

m²

SI units and conversions

Efficiency

Dimensionless or %

Power

W

Irradiance

W/m²

Area

m²

Dimensional Formula

Dimensionless

Conditions of use

  • The incident optical power and maximum electrical output power must refer to the same illuminated cell area.

  • The cell should be evaluated under specified irradiance and temperature conditions.

  • The maximum-power point must be determined from the current-voltage characteristic.

  • If P_in is calculated as GA, G must be the irradiance incident on the active area.

  • For standardized comparisons, test conditions such as irradiance, spectrum, and cell temperature must be stated.

Limitations and assumptions

  • Efficiency depends on irradiance, temperature, spectrum, and operating conditions.

  • The formula does not account separately for module wiring, inverter, or system-level losses unless those are included in the measured output.

  • Cell efficiency and complete photovoltaic-system efficiency are different quantities.

  • The maximum-power point can change with illumination and temperature.

  • Optical reflection, transmission, recombination, and resistive losses reduce practical conversion efficiency.

Step-by-step worked examples

ProblemSolutionAnswer

A solar cell receives 100 W of optical power and delivers a maximum electrical power of 20 W. Calculate its efficiency.

  • Given: P_in = 100 W and P_max = 20 W.

  • Use: η = (P_max/P_in) × 100%.

  • η = (20/100) × 100%.

  • η = 20%.

The solar-cell efficiency is 20%.

A photovoltaic cell has V_oc = 0.70 V, I_sc = 3 A, and FF = 0.75. Its incident optical power is 15 W. Calculate its efficiency.

  • Maximum output power: P_max = V_oc I_sc FF.

  • P_max = 0.70 × 3 × 0.75.

  • P_max = 1.575 W.

  • Efficiency: η = (1.575/15) × 100%.

  • η = 10.5%.

The solar-cell efficiency is 10.5%.

Real-world applications

  • Photovoltaic cell performance evaluation

  • Solar-panel technology comparison

  • Renewable-energy system design

  • Photovoltaic research and development

  • Solar-energy conversion assessment

Formula Meaning

Solar-cell efficiency is the percentage of incident optical power converted into useful electrical output power. The maximum-power expression uses the cell's maximum-power point, while the fill-factor form relates efficiency to open-circuit voltage and short-circuit current.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source