The ideal closed-loop voltage gain of a non-inverting operational-amplifier circuit is one plus the ratio of feedback resistance to the resistance connected between the inverting input and ground. The output remains in phase with the input within the circuit's operating bandwidth.
Op-Amp Closed-Loop Gain (Non-Inverting)
The ideal closed-loop voltage gain of a non-inverting operational-amplifier circuit is one plus the ratio of feedback resistance to the resistance connected between the inverting input and ground. The output remains in phase with the input within the circuit's operating bandwidth.
\(A_{\mathrm{v}} = V_{\mathrm{out}}/V_{\mathrm{in}} = 1 + R_{\mathrm{f}}/R_{\mathrm{g}}\)
What this formula means
Scientific principle
Principle
A non-inverting amplifier applies the input signal to the non-inverting terminal and uses negative feedback to establish a controlled output voltage. The op-amp adjusts its output so that the inverting and non-inverting input voltages are approximately equal.
Derivation
1. For an ideal op-amp operating with negative feedback, V_− ≈ V_+.
2. Since the input is applied to the non-inverting terminal, V_+ = V_in.
3. The inverting input receives a fraction of the output through the feedback divider.
4. The divider relation is V_− = V_out[R_g/(R_f + R_g)].
5. Set V_− = V_in.
6. Therefore, V_in = V_outR_g/(R_f + R_g).
7. Rearranging gives V_out/V_in = (R_f + R_g)/R_g = 1 + R_f/R_g.
Final Result
A_v = 1 + R_f/R_g
Output Relation
V_out = (1 + R_f/R_g)V_in
Minimum Gain
For the standard non-inverting configuration, the ideal closed-loop voltage gain is at least unity.
Variables and their meanings
| Symbol | Meaning | Unit |
|---|---|---|
A_v | Closed-loop voltage gain | Dimensionless |
V_out | Output voltage | V |
V_in | Input voltage | V |
R_f | Feedback resistance between output and inverting input | Ω |
R_g | Resistance between inverting input and ground | Ω |
SI units and conversions
Voltage Gain
Dimensionless
Resistance
Ω
Voltage
V
Dimensional Formula
Voltage gain: dimensionless
Conditions of use
The op-amp must use negative feedback.
The input signal must be applied to the non-inverting terminal.
The output must remain within the op-amp's permitted voltage range.
The op-amp should have sufficient bandwidth for the chosen closed-loop gain.
The resistor network is assumed to be ideal and purely resistive.
Limitations and assumptions
The equation assumes very high open-loop gain and negligible input current.
Real op-amps have finite gain-bandwidth product and output-current limits.
Input offset voltage and bias currents can introduce output errors.
The output cannot exceed the supply-related output swing limits.
At high frequencies, the closed-loop gain and phase response differ from the ideal resistive result.
Step-by-step worked examples
| Problem | Solution | Answer |
|---|---|---|
A non-inverting amplifier has R_f = 90 kΩ and R_g = 10 kΩ. Calculate its closed-loop voltage gain. |
| The closed-loop voltage gain is 10. |
A non-inverting amplifier has R_f = 39 kΩ, R_g = 13 kΩ, and V_in = 0.1 V. Determine its output voltage. |
| The ideal output voltage is 0.4 V. |
Real-world applications
High-input-impedance signal amplification
Sensor interface circuits
Voltage buffering with additional gain
Audio and instrumentation systems
Analog signal-conditioning circuits
Formula Meaning
The ideal closed-loop voltage gain of a non-inverting operational-amplifier circuit is one plus the ratio of feedback resistance to the resistance connected between the inverting input and ground. The output remains in phase with the input within the circuit's operating bandwidth.
Sources and further reading
No source has been supplied for this item yet. Treat the claim as needing editorial verification.