✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1537

Op-Amp Slew Rate

The slew rate of an operational amplifier is the maximum rate at which its output voltage can change with time. It is commonly expressed in volts per microsecond.

\(SR = \max|dV_{\mathrm{out}}/dt|\)

What this formula means

The slew rate of an operational amplifier is the maximum rate at which its output voltage can change with time. It is commonly expressed in volts per microsecond.

Scientific principle

Principle

An operational amplifier has internal current and capacitance limitations. During large-signal transitions, the available internal current charges or discharges compensation capacitances at a limited rate, restricting the maximum output-voltage slope.

Derivation

  • 1. The instantaneous output-voltage rate of change is dV_out/dt.

  • 2. The slew rate is defined as the maximum magnitude of this rate.

  • 3. Therefore, SR = max|dV_out/dt|.

  • 4. For an approximately linear output transition, SR can be estimated as |ΔV_out|/Δt.

  • 5. For a sinusoidal output V_out = V_p sin(2πft), the maximum slope is 2πfV_p.

  • 6. To avoid slew-rate distortion, the required maximum slope must not exceed the specified slew rate.

Final Result

SR = max|dV_out/dt|

Sinusoidal Condition

SR_required = 2πfV_p ≤ SR

Maximum Frequency

f_max = SR/(2πV_p)

Variables and their meanings

SymbolMeaningUnit

SR

Slew rate

V/s or V/μs

V_out

Output voltage

V

t

Time

s

ΔV_out

Output-voltage change during a transition

V

Δt

Time interval of the transition

s

f

Sinusoidal signal frequency

Hz

V_p

Peak output-voltage amplitude

V

SI units and conversions

Slew Rate

V/s or V/μs

Frequency

Hz

Dimensional Formula

Slew rate: [M L² T⁻⁴ I⁻¹]

Conditions of use

  • The maximum output slope should be measured under specified load and supply conditions.

  • For a sinusoidal signal, V_p must represent peak amplitude rather than peak-to-peak voltage.

  • The sinusoidal condition assumes the amplifier is expected to reproduce the waveform without slew-rate limitation.

  • The output must remain within the permitted voltage swing.

  • The manufacturer's slew-rate specification should be used for a particular op-amp.

Limitations and assumptions

  • Slew rate is a large-signal limitation and is different from small-signal bandwidth.

  • The specified slew rate can depend on supply voltage, load capacitance, and operating conditions.

  • Meeting the slew-rate condition does not guarantee low distortion; bandwidth and other limitations must also be considered.

  • The formula does not describe all nonlinear distortion mechanisms.

  • For complex waveforms, the maximum instantaneous slope rather than only the fundamental frequency must be considered.

Step-by-step worked examples

ProblemSolutionAnswer

An op-amp output changes by 10 V in 2 μs. Estimate the slew rate.

  • Given: ΔV_out = 10 V and Δt = 2 μs.

  • Use: SR ≈ |ΔV_out|/Δt.

  • SR = 10/2.

  • SR = 5 V/μs.

The estimated slew rate is 5 V/μs.

An op-amp has a slew rate of 1 V/μs and must produce a sinusoidal output with a peak amplitude of 5 V. Estimate the maximum frequency allowed by the slew-rate condition.

  • Given: SR = 1 V/μs = 1 × 10⁶ V/s and V_p = 5 V.

  • Use: f_max = SR/(2πV_p).

  • f_max = (1 × 10⁶)/(2π × 5).

  • f_max ≈ 31,831 Hz.

The theoretical slew-rate-limited maximum frequency is approximately 31.8 kHz.

Real-world applications

  • Audio amplifier design

  • High-speed signal processing

  • Waveform-generation circuits

  • Large-signal amplifier characterization

  • Operational-amplifier selection

Formula Meaning

The slew rate of an operational amplifier is the maximum rate at which its output voltage can change with time. It is commonly expressed in volts per microsecond.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source