✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1539

Differential Amplifier Gain

The ideal differential gain of a matched difference amplifier is the ratio of its feedback resistor to its input resistor. It describes how strongly the amplifier responds to the voltage difference between two input signals.

\(A_{\mathrm{d}} = V_{\mathrm{out}}/(V_2 - V_1) = R_2/R_1\)

What this formula means

The ideal differential gain of a matched difference amplifier is the ratio of its feedback resistor to its input resistor. It describes how strongly the amplifier responds to the voltage difference between two input signals.

Scientific principle

Principle

A differential amplifier amplifies the difference between two input voltages while ideally rejecting a voltage that is common to both. With matched resistor ratios, the output depends only on the differential input.

Derivation

  • 1. Consider a standard difference amplifier with input resistors R_1 and matched feedback and reference-network resistors R_2.

  • 2. The non-inverting input receives a divided version of V_2: V_+ = V_2R_2/(R_1 + R_2).

  • 3. For an ideal op-amp with negative feedback, V_− = V_+.

  • 4. Applying Kirchhoff’s Current Law at the inverting node gives (V_1 − V_−)/R_1 = (V_− − V_out)/R_2.

  • 5. Rearranging and substituting the non-inverting-node voltage gives V_out = (R_2/R_1)(V_2 − V_1).

  • 6. Dividing by the differential input gives A_d = R_2/R_1.

Final Result

V_out = (R_2/R_1)(V_2 − V_1)

Gain Relation

A_d = R_2/R_1

Note

The formula assumes the resistor ratios in the two input branches are accurately matched.

Variables and their meanings

SymbolMeaningUnit

A_d

Differential voltage gain

Dimensionless

V_out

Output voltage

V

V_1

First input voltage

V

V_2

Second input voltage

V

R_1

Input resistance in each matched input branch

Ω

R_2

Feedback and corresponding reference-branch resistance

Ω

SI units and conversions

Differential Gain

Dimensionless

Voltage

V

Resistance

Ω

Dimensional Formula

Differential voltage gain: dimensionless

Conditions of use

  • The amplifier must use negative feedback and operate in its linear range.

  • The two resistor ratios must be matched.

  • The op-amp input common-mode voltage must remain within its permitted range.

  • The output must remain within the supply-related voltage limits.

  • The stated sign convention assumes V_2 is applied to the non-inverting-side divider and V_1 to the inverting-side input.

Limitations and assumptions

  • Resistor mismatch causes common-mode signal leakage into the output.

  • Finite op-amp open-loop gain and bandwidth cause deviations from the ideal gain.

  • Input offset voltage and bias currents can introduce output errors.

  • The output may saturate for large differential inputs.

  • The equation describes differential gain, not common-mode gain.

Step-by-step worked examples

ProblemSolutionAnswer

A difference amplifier has R_1 = 10 kΩ and R_2 = 100 kΩ. Calculate its differential gain.

  • Given: R_1 = 10 kΩ and R_2 = 100 kΩ.

  • Use: A_d = R_2/R_1.

  • A_d = 100/10.

  • A_d = 10.

The differential gain is 10.

A matched difference amplifier has R_1 = 5 kΩ, R_2 = 25 kΩ, V_1 = 0.2 V, and V_2 = 0.5 V. Calculate the output voltage.

  • Gain: A_d = 25/5 = 5.

  • Differential input: V_2 − V_1 = 0.5 − 0.2 = 0.3 V.

  • Output: V_out = A_d(V_2 − V_1).

  • V_out = 5 × 0.3.

  • V_out = 1.5 V.

The ideal output voltage is 1.5 V.

Real-world applications

  • Differential sensor interfaces

  • Bridge measurement circuits

  • Noise-resistant signal conditioning

  • Instrumentation systems

  • Analog computation and subtraction circuits

Formula Meaning

The ideal differential gain of a matched difference amplifier is the ratio of its feedback resistor to its input resistor. It describes how strongly the amplifier responds to the voltage difference between two input signals.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source