✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-ENG-1793

Poisson’s Ratio from Seismic Velocities

Poisson’s ratio can be estimated from measured P-wave and S-wave velocities in an isotropic linear elastic material. It describes the ratio of transverse contraction strain to longitudinal extension strain under uniaxial loading.

\(\nu = (v_{\mathrm{P}}^{2} - 2v_{\mathrm{S}}^{2})/[2(v_{\mathrm{P}}^{2} - v_{\mathrm{S}}^{2})]\)

What this formula means

Poisson’s ratio can be estimated from measured P-wave and S-wave velocities in an isotropic linear elastic material. It describes the ratio of transverse contraction strain to longitudinal extension strain under uniaxial loading.

Scientific principle

Principle

P-wave velocity depends on both bulk and shear stiffness, whereas S-wave velocity depends on shear stiffness alone. Their relationship therefore provides information about the elastic properties of a material, including Poisson's ratio.

Derivation

  • 1. For an isotropic elastic solid, v_P² = (K + 4μ/3)/ρ.

  • 2. The S-wave relation is v_S² = μ/ρ.

  • 3. The elastic relation between bulk modulus and shear modulus is K = 2μ(1 + ν)/[3(1 − 2ν)].

  • 4. Substituting these relations and eliminating K, μ, and ρ gives the relationship between the velocity ratio and Poisson's ratio.

  • 5. Rearranging the resulting expression gives ν = (v_P² − 2v_S²)/[2(v_P² − v_S²)].

Final Result

ν = (v_P² − 2v_S²)/[2(v_P² − v_S²)]

Velocity Ratio Form

ν = [((v_P/v_S)² − 2)]/[2((v_P/v_S)² − 1)]

Variables and their meanings

SymbolMeaningUnit

ν

Poisson's ratio

Dimensionless

v_P

P-wave velocity

m/s

v_S

S-wave velocity

m/s

SI units and conversions

Poissons Ratio

Dimensionless

Seismic Velocities

m/s

Dimensional Formula

Dimensionless

Conditions of use

  • The material is assumed to be isotropic and linearly elastic.

  • Both velocities should represent the same material region and comparable measurement conditions.

  • The material should have a nonzero shear-wave velocity.

  • P-wave and S-wave velocities must use the same velocity units.

  • The equation is most appropriate when the measured waves can be interpreted using an isotropic elastic model.

Limitations and assumptions

  • Anisotropic rocks may not have a single direction-independent Poisson's ratio.

  • Fractures, layering, porosity, and fluid saturation can complicate the inferred elastic properties.

  • Measurement errors in either velocity affect the calculated ratio.

  • The equation does not independently determine bulk modulus, shear modulus, or density.

  • The formula is not directly applicable to an ideal fluid with zero shear-wave velocity.

Step-by-step worked examples

ProblemSolutionAnswer

A rock has P-wave velocity 6,000 m/s and S-wave velocity 3,500 m/s. Estimate its Poisson's ratio.

  • Given: v_P = 6,000 m/s and v_S = 3,500 m/s.

  • Use: ν = (v_P² − 2v_S²)/[2(v_P² − v_S²)].

  • v_P² = 36,000,000.

  • v_S² = 12,250,000.

  • Numerator = 36,000,000 − 24,500,000 = 11,500,000.

  • Denominator = 2(36,000,000 − 12,250,000) = 47,500,000.

  • ν = 11,500,000/47,500,000.

  • ν ≈ 0.242.

The estimated Poisson's ratio is approximately 0.242.

A solid has P-wave velocity 5 km/s and S-wave velocity 3 km/s. Calculate its Poisson's ratio.

  • Given: v_P = 5 km/s and v_S = 3 km/s.

  • Use: ν = (v_P² − 2v_S²)/[2(v_P² − v_S²)].

  • ν = (25 − 2 × 9)/[2(25 − 9)].

  • ν = 7/32.

  • ν = 0.21875.

The estimated Poisson's ratio is approximately 0.219.

Real-world applications

  • Elastic-property estimation from seismic surveys

  • Rock-mechanics characterization

  • Subsurface lithology interpretation

  • Geotechnical investigation

  • Seismic reservoir characterization

Formula Meaning

Poisson’s ratio can be estimated from measured P-wave and S-wave velocities in an isotropic linear elastic material. It describes the ratio of transverse contraction strain to longitudinal extension strain under uniaxial loading.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source