✦ScienexySCIENCE KNOWLEDGE LIBRARY
General science · SCI-FORM-MED-1358

First-Order Elimination Rate

First-order elimination describes a process in which the amount of drug eliminated per unit time is proportional to the amount remaining in the body. The fraction eliminated per unit time remains constant under suitable conditions.

\(-dA/dt = kA; A_{\mathrm{t}} = A_{0}e^{-kt}\)

What this formula means

First-order elimination describes a process in which the amount of drug eliminated per unit time is proportional to the amount remaining in the body. The fraction eliminated per unit time remains constant under suitable conditions.

Scientific principle

Principle

When elimination follows first-order kinetics, a constant proportion of the remaining drug is removed during each equal time interval. This produces an exponential decline in drug amount or concentration.

Derivation

  • Let A represent the amount of drug remaining in the body.

  • The elimination rate is proportional to A.

  • Write dA/dt = −kA, where k is the positive first-order elimination constant.

  • Separate variables: dA/A = −k dt.

  • Integrate: ln(A_t/A₀) = −kt.

  • Exponentiate: A_t = A₀e^(−kt).

  • For a constant apparent distribution volume, concentration follows the same exponential form.

Final Result

A_t = A₀e^(−kt). The elimination rate magnitude is kA.

Variables and their meanings

A t

Amount of drug remaining at time t.

A₀

Initial amount of drug.

K

First-order elimination rate constant.

T

Elapsed time.

D A/dt

Rate of change of drug amount.

SI units and conversions

Amount

mg or μg.

K

time⁻¹, such as h⁻¹.

Time

h, min or s.

Elimination Rate

mg·h⁻¹.

Dimensional Formula Of K

T⁻¹.

Conditions of use

  • Elimination rate must be proportional to the amount remaining.

  • The rate constant should remain approximately constant.

  • The model should be applied over a concentration range where elimination is not saturated.

  • The selected compartment or amount definition must remain consistent.

Limitations and assumptions

  • The model does not describe saturated elimination processes.

  • Clearance and metabolic capacity may change with concentration or physiological condition.

  • Multicompartment distribution may produce more complex concentration-time profiles.

  • The equation does not independently describe drug absorption.

  • A first-order approximation may be valid only over a limited concentration range.

Step-by-step worked examples

ProblemSolutionAnswer

A theoretical compound begins with an amount of 80 mg. Its first-order elimination constant is 0.20 h⁻¹. Determine the remaining amount after 3 hours.

  • A_t = A₀e^(−kt).

  • A_t = 80e^(−0.20 × 3).

  • A_t = 80e^(−0.6).

  • A_t ≈ 80 × 0.5488.

  • A_t ≈ 43.90 mg.

The modeled remaining amount is approximately 43.9 mg.

A theoretical compound has an initial amount of 120 mg and a first-order elimination constant of 0.15 h⁻¹. Calculate the instantaneous elimination rate when 40 mg remains.

  • The magnitude of the first-order elimination rate is kA.

  • Rate = 0.15 h⁻¹ × 40 mg.

  • Rate = 6 mg·h⁻¹.

The instantaneous elimination rate magnitude is 6 mg·h⁻¹.

Real-world applications

  • Modeling exponential drug elimination.

  • Interpreting concentration-time curves.

  • Estimating elimination rate constants.

  • Studying pharmacokinetic half-life.

  • Comparing linear pharmacokinetic behavior across compounds.

Formula Meaning

First-order elimination describes a process in which the amount of drug eliminated per unit time is proportional to the amount remaining in the body. The fraction eliminated per unit time remains constant under suitable conditions.

Sources and further reading

No source has been supplied for this item yet. Treat the claim as needing editorial verification.

← Back to Formula Hub · Suggest a correction or source