An analytical result is produced by a sequence of connected operations rather than by an instrument alone. This sequence is known as the analytical workflow. Each stage can influence the final result, and errors introduced early in the process may remain undetected even when the final instrument measurement is performed correctly.
The workflow begins by defining the analytical problem. The analyst must identify the target analyte, the sample type, the required concentration range, and the purpose of the measurement. For example, measuring lead in drinking water requires different analytical performance from measuring a major mineral component in an ore sample.
Sampling follows. The collected portion must represent the material or population being studied. Sample preparation may then be required to remove unwanted particles, dissolve the analyte, decompose the matrix, concentrate the analyte, or convert it into a form suitable for measurement.
Method selection considers sensitivity, selectivity, accuracy, precision, cost, time, equipment, and sample compatibility. The analyst then prepares standards, blanks, and quality-control samples and performs the measurement under controlled conditions.
Data processing includes blank correction, dilution calculations, calibration, statistical evaluation, and uncertainty assessment. Finally, the result is reported with its unit, method, relevant conditions, and any limitations that affect interpretation.
The workflow is iterative. If a quality-control result fails, the analyst may need to investigate calibration, sample preparation, instrument condition, or contamination before reporting the result.
Analytical Chemistry Workflow
An analytical chemistry workflow is the organized sequence of activities used to obtain a reliable answer to a chemical question. It includes defining the problem, sampling, sample preparation, method selection, measurement, calibration, data evaluation, quality control, and reporting.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
C₁ | Initial concentration | Concentration unit |
V₁ | Initial aliquot volume | L or mL |
C₂ | Final concentration | Same concentration unit as C₁ |
V₂ | Final solution volume | Same volume unit as V₁ |
y | Measured analytical response | Instrument-dependent |
a | Calibration intercept | Same as y |
b | Calibration slope | Response per concentration unit |
c | Analyte concentration | Method-dependent concentration unit |
Example or application
A worked example has not yet been added.
Definition
An analytical chemistry workflow is a structured sequence of procedures through which a chemical problem is converted into a reliable, interpretable analytical result.
Purpose
Organize laboratory activities systematically.
Reduce avoidable errors and improve measurement reliability.
Ensure that sampling and preparation are treated as essential analytical stages.
Provide traceability from the original sample to the final reported result.
Key Concepts
| Term | Meaning |
|---|---|
Measurand | The quantity intended to be measured. |
Sampling | The process of selecting a portion of material for analysis. |
Sample preparation | Operations used to make a sample suitable for the chosen analytical method. |
Calibration | Establishing the relationship between instrument response and known reference values. |
Quality control | Checks used to monitor whether an analytical procedure is performing acceptably. |
Traceability | The ability to relate a result to appropriate references through a documented chain of calibrations or comparisons. |
Principle
The reliability of a final analytical result depends on the combined performance of every relevant stage in the workflow. A reliable measurement therefore requires a defined measurand, representative sampling, suitable preparation, a fit-for-purpose method, controlled measurement, valid data processing, and appropriate quality assurance.
Workflow Stages
| Step | Name | Description | Example |
|---|---|---|---|
1 | Problem definition | Specify the analyte, sample matrix, required range, intended use, and required analytical performance. | Determine whether a drinking-water sample contains lead above a specified decision level. |
2 | Sampling | Collect representative portions using a suitable sampling design and clean equipment. | Collect water from defined locations using appropriate sample containers. |
3 | Sample preservation and preparation | Prevent analyte loss or transformation and prepare the sample for measurement. | Filter or acidify a sample only when the selected method and measurand require it. |
4 | Method selection | Choose a method with adequate selectivity, sensitivity, range, and reliability. | Select an appropriate atomic spectroscopy method for trace metal measurement. |
5 | Calibration and quality control | Prepare standards, blanks, and check samples to establish and monitor measurement performance. | Measure calibration standards and a suitable quality-control sample. |
6 | Measurement | Measure samples using the documented procedure and controlled instrument conditions. | Record the instrument response for each prepared sample. |
7 | Data processing | Apply the calibration relationship, dilution factors, blank corrections, and required calculations. | Convert a measured diluted-sample concentration into the original-sample concentration. |
8 | Quality evaluation | Check blanks, control samples, replicate agreement, calibration performance, and uncertainty. | Investigate a control result outside its established acceptance limits. |
9 | Reporting | Present the result with analyte, unit, sample identity, method, and relevant qualifications. | Report lead concentration in µg L⁻¹ with an uncertainty statement when required. |
Equations
| Name | Expression | Description |
|---|---|---|
Dilution relationship | C₁V₁ = C₂V₂ | For a simple dilution in which the amount of analyte is conserved, the initial and final concentration-volume products are equal. |
Calibration relationship | y = a + bc | A common linear calibration model relating measured response y to analyte concentration c, with intercept a and slope b. |
Units
mol L⁻¹
mg L⁻¹
µg L⁻¹
mg kg⁻¹
mL
L
Worked Example
Problem
A water sample is diluted by transferring 10.00 mL of the original sample into a 100.0 mL volumetric flask and filling to the mark. The diluted sample gives a concentration of 2.50 mg L⁻¹. Calculate the original concentration.
Steps
Given: V₁ = 10.00 mL.
Final volume: V₂ = 100.0 mL.
Measured diluted concentration: C₂ = 2.50 mg L⁻¹.
Use C₁V₁ = C₂V₂.
Rearrange: C₁ = C₂V₂/V₁.
C₁ = 2.50 × 100.0/10.00.
Answer
The original sample concentration is 25.0 mg L⁻¹, assuming the dilution was performed correctly and no analyte was lost or added.
Quality Control Elements
Reagent blank: checks contributions from reagents and preparation steps.
Method blank: checks contamination introduced by the complete preparation procedure.
Calibration verification standard: checks whether the calibration remains valid.
Replicate sample: evaluates repeatability under the specified procedure.
Certified reference material: helps evaluate measurement bias when a suitable material is available.
Control chart: monitors analytical performance over time.
Applications
Routine environmental monitoring.
Pharmaceutical batch testing.
Food quality and contaminant analysis.
Clinical laboratory measurement.
Industrial process monitoring.
Research laboratory investigations.
Advantages
Makes analytical work systematic and traceable.
Helps identify where errors or contamination may have occurred.
Improves consistency between analysts and measurement batches.
Supports reliable reporting and laboratory quality systems.
Limitations
A workflow must be adapted to the analyte and sample matrix.
Some stages may be time-consuming or expensive.
A documented workflow does not guarantee quality unless it is properly implemented.
Unexpected matrix effects or sample instability may require method development or additional investigation.
Common Mistakes
Starting measurements without defining the measurand.
Ignoring sample representativeness.
Using inappropriate preservation or preparation conditions.
Failing to include suitable blanks and quality-control samples.
Applying a calibration curve outside its validated range.
Reporting results before investigating failed quality-control checks.
Learning Objectives
Define an analytical workflow.
List and explain the main stages of analytical work.
Explain why sampling and preparation affect final results.
Describe the role of calibration and quality control.
Calculate the original concentration after a simple dilution.
Recognize when an analytical result should be investigated before reporting.
Practice Questions
List the major stages of an analytical chemistry workflow.
Why must the analytical problem be clearly defined before selecting a method?
What is the purpose of a method blank?
Differentiate between calibration and quality control.
A sample is diluted from 5.00 mL to 50.0 mL. If its diluted concentration is 1.20 mg L⁻¹, calculate the original concentration.
What should an analyst do if a quality-control sample fails its acceptance criterion?
Key Takeaways
An analytical result is produced by a complete workflow, not by an instrument alone.
Sampling and preparation can strongly influence the final measurement.
Calibration establishes the response relationship, while quality control monitors performance.
Results should be reported only after relevant quality checks have been evaluated.
References
| Title | Authors | Edition | Type | Scope | Url |
|---|---|---|---|---|---|
Quantitative Chemical Analysis | Daniel C. Harris and Charles A. Lucy | 10th edition | Textbook | Analytical procedure, calibration, and quantitative measurement. | |
Eurachem Guide: The Fitness for Purpose of Analytical Methods | Technical guide | Method performance and fitness for purpose. | https://eurachem.org/index.php/publications/guides | ||
ISO/IEC 17025:2017 | International standard | General requirements for the competence of testing and calibration laboratories. |
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Analytical Chemistry