A collected laboratory sample may contain components distributed unevenly. Before taking a small test portion, the material often needs to be homogenized so that different portions have similar composition at the relevant scale. Homogenization may involve mixing, blending, stirring, grinding, or other suitable operations. Sample reduction decreases the quantity of material while attempting to preserve its composition and representativeness. Common reduction methods include coning and quartering, riffle splitting, rotary sample division, and mechanical splitting. The choice depends on particle size, moisture, cohesion, sample quantity, and the risk of segregation. Simply taking a scoop from the top of a container may produce a biased test portion if particles differ in size or density. Fine particles may concentrate in particular regions, while coarse particles may settle or separate during handling. Homogenization and reduction should therefore be treated as controlled operations rather than casual mixing and removal. Some materials cannot be homogenized by dry mixing because they are sticky, chemically unstable, or prone to particle segregation. The procedure should be validated or checked using replicate portions when sample heterogeneity is important.
Sample Homogenization and Reduction
Sample homogenization and reduction are preparation operations used to make a laboratory sample more uniform and obtain a smaller test portion without significantly changing its composition. They are particularly important for heterogeneous solids, powders, foods, ores, and particulate materials.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
x₁, x₂ | Results from two test portions | Same as the measured quantity |
RPD | Relative percent difference | % |
m₀ | Initial sample mass | g or kg |
m₁, m₂ | Masses of retained portions | g or kg |
mₗ | Documented mass loss | g or kg |
Example or application
A worked example has not yet been added.
Definition
Homogenization is the process of making a material more uniform in composition or distribution, while sample reduction is the controlled decrease of sample quantity to obtain a smaller representative portion.
Purpose
To improve uniformity and obtain a manageable test portion that retains the relevant composition of the original laboratory sample.
Importance
An analytical test portion is often much smaller than the original material. Without suitable homogenization and reduction, the selected portion may contain an unrepresentative amount of analyte and produce misleading results.
Key Concepts
Homogenization: improvement of compositional uniformity.
Sample reduction: controlled decrease in sample quantity.
Test portion: quantity used for an individual analytical determination.
Segregation: separation of particles according to physical properties.
Coning and quartering: manual sample-reduction technique involving mixing, coning, flattening, and dividing.
Riffle splitter: device that divides a flowing or poured sample into alternating portions.
Rotary sample divider: equipment that distributes sample increments into separate containers.
Particle-size distribution: relative abundance of particles of different sizes.
Subsampling: selection of a smaller portion from a larger sample.
Compositional uniformity: similarity of composition among different portions.
Principle
The central principle is to reduce sample quantity without systematically changing the proportions of its components. Effective mixing improves uniformity, while appropriate splitting distributes particles across the resulting portions. The method must minimize segregation, material loss, contamination, and changes in moisture or chemical composition.
Working Process
Inspect the sample and identify its physical state, moisture, particle size, and visible heterogeneity.
Select a suitable homogenization procedure compatible with the material.
Mix or blend the sample using controlled conditions.
Break up agglomerates only when the analytical objective permits it.
Select an appropriate reduction method, such as a riffle splitter or coning and quartering.
Avoid selective removal of particles or portions.
Collect the reduced sample in a clean, compatible container.
Repeat mixing or splitting if necessary to obtain the required quantity.
Check homogeneity using replicate test portions when justified.
Equations
| Name | Expression | Description | Conditions |
|---|---|---|---|
Relative percent difference between two test portions | RPD (%) = |x₁ - x₂| / [(x₁ + x₂) / 2] × 100 | Compares two results obtained from separate portions and can help assess the combined variability of subsampling and analysis. | The results must use the same units and have a nonzero mean. |
Mass balance during sample reduction | m₀ = m₁ + m₂ + mₗ | Relates initial mass to the masses of retained portions and any documented material loss. | All mass fractions must be measured on a consistent basis. |
Units
Sample mass: g or kg
Particle size: µm or mm
Moisture content: % by mass
Relative percent difference: %
Examples
| Title | Problem | Solution | Learning Point | Answer |
|---|---|---|---|---|
Coning and quartering of a solid sample | A laboratory has a large quantity of dry granular material but needs a smaller representative portion. | The material is mixed and formed into a cone. The cone is flattened and divided into four approximately equal sectors. Opposite sectors are combined, while the remaining sectors are set aside. The retained portion can be mixed and reduced again if a smaller quantity is needed. | The method attempts to distribute components across the retained portion, but it must be performed carefully to minimize particle segregation. | |
Checking test-portion agreement | Two independently prepared portions produce results of 12.0 mg/kg and 12.6 mg/kg. Calculate their RPD. | Mean = (12.0 + 12.6) / 2 = 12.3 mg/kg. RPD = 0.6 / 12.3 × 100 ≈ 4.88%. | Replicate portions can provide evidence about subsampling variability, although acceptance depends on the method and material. | The relative percent difference is approximately 4.88%. |
Applications
Preparation of soil and sediment samples.
Homogenization of food products before compositional analysis.
Reduction of mineral and ore samples.
Preparation of pharmaceutical powders.
Subsampling of industrial raw materials.
Preparation of solid waste samples for contaminant testing.
Advantages
Improves uniformity before analytical testing.
Reduces large samples to manageable quantities.
Can reduce variation between test portions.
Supports more reproducible analytical measurements.
Limitations
Some materials are difficult to homogenize because of moisture, cohesion, or chemical instability.
Mixing can cause particle segregation instead of preventing it.
Grinding may change the physical or chemical properties of a sample.
Manual reduction can introduce operator-dependent variation.
A reduced sample may remain unrepresentative if the initial sample was poorly collected.
Common Mistakes
Taking a test portion directly from the top of an unmixed container.
Assuming visual uniformity proves chemical homogeneity.
Ignoring particle-size and density differences.
Using an inappropriate splitter for sticky or wet materials.
Losing fine particles during transfer.
Overmixing or grinding a material that is chemically unstable.
Reducing the sample before adequately mixing it.
Prerequisites
Introduction to analytical sampling.
Representative sampling.
Basic knowledge of solid materials and particle size.
Learning Objectives
Define homogenization and sample reduction.
Explain why a test portion must represent the laboratory sample.
Describe coning and quartering.
Explain the role of riffle and rotary sample dividers.
Identify how segregation affects sample composition.
Calculate the relative percent difference between test-portion results.
Practice Questions
What is the difference between homogenization and sample reduction?
Why is taking a scoop from the top of a powder container potentially unreliable?
Describe the basic principle of coning and quartering.
How can particle-size differences cause segregation?
Two portions produce 25 mg/kg and 27 mg/kg. Calculate their RPD.
Why might grinding be unsuitable for certain samples?
Key Takeaway
Homogenization and reduction must preserve the composition of the material while producing a manageable test portion. The original sample's representativeness cannot be improved if the initial collection was fundamentally biased.
References
| Title | Authors | Type | Relevance |
|---|---|---|---|
Quantitative Chemical Analysis | Daniel C. Harris and Charles A. Lucy | textbook | Sample preparation and representative analytical portions. |
Gy's Sampling Theory and Practice | Pierre M. Gy | technical reference | Fundamental theory of sampling particulate materials. |
ISO 11648 Series: Statistical Aspects of Sampling from Bulk Materials | international standard series | Statistical considerations in bulk-material sampling. |
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Analytical Chemistry