✦ScienexySCIENCE KNOWLEDGE LIBRARY
topic · SCI-CHE-005-019

Drying, Grinding, and Sieving

Drying, grinding, and sieving are physical sample-preparation operations used to control moisture, reduce particle size, and separate particles according to size. These procedures improve sample handling and may increase uniformity, but they must be selected carefully to avoid analyte loss or chemical alteration.

Explanation

Solid samples often require physical preparation before chemical analysis. Drying removes moisture under controlled conditions and may allow results to be reported on a dry-mass basis. However, heating can cause loss of volatile analytes, decomposition, oxidation, dehydration, or changes in chemical form. Some samples therefore require air drying, freeze-drying, low-temperature drying, or analysis without drying. Grinding reduces particle size and can improve mixing, dissolution, and reaction rates by increasing surface area. Grinding equipment must be selected to minimize contamination from metal, ceramic, or other grinding surfaces. Excessive grinding can generate heat, cause volatile losses, or alter mineral phases. Sieving separates particles into size fractions using meshes with defined openings. The resulting fractions can be used to study particle-size-dependent composition or prepare a material within a specified size range. Drying, grinding, and sieving are not universally required and should not be performed automatically. Their suitability depends on the sample and analytical objective. The preparation procedure must preserve the analyte and must be documented because it can affect the measured result.

Variables

SymbolMeaningUnit

mwet

Initial wet sample mass

g or kg

mdry

Mass after drying

g or kg

w

Moisture mass fraction on a wet basis

Dimensionless

Cwet

Concentration on a wet-mass basis

mg/kg wet sample or equivalent

Cdry

Concentration on a dry-mass basis

mg/kg dry sample or equivalent

Example or application

A worked example has not yet been added.

Definition

Drying removes moisture from a sample, grinding reduces particle size through mechanical action, and sieving separates particles according to their ability to pass through openings of defined dimensions.

Purpose

To control sample moisture, improve physical uniformity, facilitate dissolution or extraction, and obtain particle-size fractions suitable for subsequent analysis.

Importance

Moisture and particle size can influence sample mass, concentration calculations, dissolution rates, extraction efficiency, and reproducibility. Controlled preparation helps ensure that analytical results are comparable and correctly interpreted.

Key Concepts

  • Dry-mass basis: concentration or composition expressed relative to the mass of dry material.

  • Moisture content: amount of water present in a material relative to a defined mass basis.

  • Oven drying: removal of moisture using controlled heating.

  • Freeze-drying: removal of water through freezing followed by sublimation under reduced pressure.

  • Grinding: mechanical reduction of particle size.

  • Surface area: exposed area of material that can participate in dissolution or reaction.

  • Sieving: particle-size separation using a mesh or screen.

  • Sieve aperture: nominal opening size of a sieve.

  • Contamination: introduction of foreign material during preparation.

  • Volatile analyte: analyte that can enter the gas phase under the conditions used.

Principle

Drying changes the sample's water content, grinding changes particle dimensions and surface area, and sieving separates particles according to size. These operations are useful only when the physical changes do not compromise the chemical property being measured.

Working Process

  • Identify the analytical objective and determine whether drying, grinding, or sieving is necessary.

  • Assess analyte volatility, thermal stability, oxidation sensitivity, and sample moisture.

  • Select a drying method and conditions compatible with the analyte.

  • Dry the sample to the method-defined condition and cool it appropriately before weighing when required.

  • Select clean grinding equipment that minimizes contamination.

  • Grind the material using controlled conditions and avoid excessive heating.

  • Choose sieves with suitable nominal apertures.

  • Sieve the material and collect the required particle-size fraction.

  • Store prepared material in a compatible container and document preparation conditions.

Equations

NameExpressionDescriptionConditions

Moisture content on a wet-mass basis

Moisture (%) = [(mwet - mdry) / mwet] × 100

Calculates the percentage of initial sample mass lost during drying when the mass loss is attributed to moisture.

The drying procedure must not cause significant loss of non-water components.

Dry-mass fraction

Dry-mass fraction = mdry / mwet

Represents the fraction of the original wet sample mass remaining after drying.

The wet and dry masses must refer to the same sample and drying basis.

Conversion to dry-mass-basis concentration

Cdry = Cwet / (1 - w)

Converts a wet-mass-basis concentration to a dry-mass-basis concentration when w is the moisture mass fraction on a wet basis.

The analyte mass is assumed unchanged during drying.

Units

  • Sample mass: g or kg

  • Moisture content: %

  • Particle size: µm or mm

  • Sieve aperture: µm or mm

  • Drying temperature: °C or K

  • Drying time: min or h

Examples

TitleProblemSolutionAnswerLearning Point

Calculating moisture content

A soil sample has an initial mass of 50.0 g and a dry mass of 42.0 g. Calculate its moisture content on a wet-mass basis.

Moisture (%) = [(50.0 - 42.0) / 50.0] × 100 = 16.0%.

The moisture content is 16.0%.

The calculation assumes that the mass lost during the specified drying procedure represents water.

Converting concentration to a dry-mass basis

A material contains 80 mg/kg analyte on a wet-mass basis and has a moisture fraction of 0.20. Calculate the dry-mass-basis concentration.

Cdry = 80 / (1 - 0.20) = 80 / 0.80 = 100 mg/kg.

The dry-mass-basis concentration is 100 mg/kg.

The conversion assumes that the analyte is not lost or transformed during moisture removal.

Applications

  • Preparation of soil and sediment for elemental analysis.

  • Moisture determination in food and agricultural products.

  • Particle-size classification of powders and mineral materials.

  • Preparation of samples for dissolution and digestion.

  • Quality control of pharmaceutical powders.

  • Study of particle-size-dependent chemical composition.

Advantages

  • Drying can improve mass-basis consistency.

  • Grinding can improve sample uniformity and dissolution efficiency.

  • Sieving provides controlled particle-size fractions.

  • Standardized preparation improves comparability between analyses.

Limitations

  • Drying can remove volatile analytes or change chemical forms.

  • Grinding equipment can introduce contaminants.

  • Fine particles may be lost during transfer and sieving.

  • Grinding can cause heating, oxidation, or phase changes.

  • Particle-size separation may change the composition of the collected fraction.

Common Mistakes

  • Drying every sample at the same temperature without considering analyte stability.

  • Assuming all mass loss during heating is water.

  • Using contaminated or chemically incompatible grinding equipment.

  • Ignoring the loss of fine particles during grinding and sieving.

  • Reporting dry-basis and wet-basis concentrations as if they were identical.

  • Using sieving without recording the sieve aperture.

Prerequisites

  • Sample homogenization and reduction.

  • Basic mass measurements and concentration calculations.

  • Understanding of physical properties of solids.

Learning Objectives

  • Explain the purposes of drying, grinding, and sieving.

  • Calculate moisture content on a wet-mass basis.

  • Convert concentration from wet-mass to dry-mass basis.

  • Explain how particle-size reduction affects surface area.

  • Identify possible sources of contamination during grinding.

  • Explain why drying conditions must be selected according to analyte stability.

Practice Questions

  • Why is drying performed before some chemical analyses?

  • A sample weighs 80 g before drying and 68 g afterward. Calculate its wet-basis moisture content.

  • How can grinding improve dissolution?

  • Why may grinding introduce contamination?

  • What is the purpose of sieving?

  • A material has a wet-basis concentration of 40 mg/kg and a moisture fraction of 0.25. Calculate its dry-basis concentration.

  • Why is oven drying unsuitable for some volatile analytes?

Key Takeaway

Drying, grinding, and sieving are useful physical preparation techniques, but their conditions must be selected to preserve the analyte and avoid changing the composition of the material.

References

TitleAuthorsTypeRelevance

Quantitative Chemical Analysis

Daniel C. Harris and Charles A. Lucy

textbook

Sample preparation and quantitative measurement.

Standard Methods for the Examination of Water and Wastewater

APHA, AWWA, and WEF

standard analytical reference

Sample preparation and measurement procedures.

ISO 11464: Soil Quality — Pretreatment of Samples for Physico-Chemical Analysis

international standard

Pretreatment of soil samples.

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.

Suggest a correction or source · More in Analytical Chemistry