Sample contamination occurs when an unwanted substance enters a sample from equipment, containers, reagents, the environment, personnel, or another sample. At high analyte concentrations, minor contamination may have little effect, but in trace analysis even extremely small quantities can produce substantial positive bias. Contamination can occur during field collection, transport, storage, digestion, filtration, dilution, and instrumental measurement. Common sources include dust, fingerprints, residues from previously analyzed samples, impure reagents, contaminated water, metal tools, lubricants, cleaning agents, and container leaching. Cross-contamination occurs when material from one sample enters another. Carryover is a related problem in which analyte remaining in an instrument or sample-introduction system affects a subsequent measurement. Prevention requires clean work areas, suitable containers, appropriate cleaning procedures, dedicated equipment where necessary, careful sample identification, and controlled handling. Quality-control samples such as field blanks, trip blanks, equipment blanks, method blanks, and laboratory control samples help identify different sources of contamination. A blank is not a substitute for good laboratory practice; it is evidence used to assess contamination under defined conditions.
Contamination and Sample Handling
Contamination and sample handling concern the prevention, detection, and control of unwanted substances introduced into a sample during collection, preparation, storage, and analysis. Proper handling is especially important in trace analysis, where very small amounts of contamination can significantly affect the measured result.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
Snet | Net analytical response | Same as the instrument response |
Ssample | Measured sample response | Instrument-dependent |
Sblank | Measured blank response | Same as sample response |
Cblank | Concentration measured in the blank | mg/L, µg/L, or another concentration unit |
Csample | Concentration measured in the sample | Same as blank concentration |
Example or application
A worked example has not yet been added.
Definition
Sample contamination is the unintended introduction of foreign substances into a sample, while sample handling refers to the controlled procedures used to collect, transfer, prepare, store, and protect samples throughout the analytical process.
Purpose
To prevent contamination, sample loss, mix-ups, and unwanted changes that could compromise analytical accuracy and reliability.
Importance
Contamination can cause false-positive findings, biased concentrations, poor precision, and invalid conclusions. Careful handling is essential for reliable analysis, particularly at low analyte concentrations.
Key Concepts
Contamination: introduction of unwanted material into a sample.
Cross-contamination: transfer of material between samples.
Carryover: residual analyte or sample material affecting a subsequent measurement.
Field blank: blank material exposed to field sampling conditions.
Trip blank: blank transported with samples to assess contamination during transport.
Equipment blank: blank used to evaluate contamination from sampling equipment.
Method blank: blank processed through the analytical preparation procedure.
Reagent blank: blank used to assess contributions from reagents.
Laboratory control sample: a sample with known or established characteristics used to assess analytical performance.
Trace analysis: measurement of very low analyte concentrations.
Sample identity: unique information used to distinguish one sample from another.
Chain of custody: documented record of sample possession and transfer.
Principle
Reliable handling minimizes the introduction, loss, or transformation of sample components. Contamination control combines preventive practices with quality-control checks. Different blank types are designed to investigate different stages of the process, and their results must be interpreted according to where and how each blank was exposed.
Working Process
Identify potential contamination sources associated with the sample, analyte, and analytical method.
Select containers and equipment compatible with the sample and required detection level.
Clean or prepare equipment using a documented procedure.
Use suitable personal protective equipment and clean handling practices.
Collect samples without touching internal container surfaces or introducing foreign material.
Keep samples properly sealed, labelled, and separated during transport.
Use clean reagents, water, and preparation equipment.
Include appropriate blanks and other quality-control samples.
Prevent sample carryover through validated cleaning and instrument-wash procedures.
Investigate unexpected blank results or evidence of contamination before reporting sample results.
Equations
| Name | Expression | Description | Conditions |
|---|---|---|---|
Blank-corrected analytical response | Snet = Ssample - Sblank | Subtracts the blank response from the sample response when the blank represents the relevant background contribution and the method permits this correction. | The sample and blank responses must be measured under compatible conditions. |
Blank contribution relative to sample concentration | Blank contribution (%) = (Cblank / Csample) × 100 | Expresses the blank concentration as a percentage of the sample concentration. | The concentrations must use the same units and the sample concentration must be nonzero. |
Units
Analyte concentration: mg/L, µg/L, ng/L, or mg/kg
Sample mass: g or kg
Sample volume: mL or L
Blank contribution: %
Cleaning solution concentration: method-dependent
Examples
| Title | Problem | Solution | Answer | Learning Point |
|---|---|---|---|---|
Evaluating blank contamination | A water sample contains 10 µg/L of an analyte, while the associated method blank contains 0.5 µg/L. Calculate the blank contribution relative to the sample concentration. | Blank contribution (%) = (0.5 / 10) × 100 = 5%. | The blank contribution is 5% of the sample concentration. | Whether this contribution is acceptable depends on the method's quality-control criteria and the intended measurement level. |
Identifying a contamination source | A field blank contains measurable metal, while the laboratory method blank is below the reporting limit. | The difference suggests that contamination may have entered during field collection, equipment handling, or transport rather than during the laboratory digestion procedure. Equipment blanks and other controls can help identify the specific source. | Blank results are most useful when the blank type represents a clearly defined stage of the sampling and analytical process. |
Applications
Trace-metal analysis in environmental samples.
Pharmaceutical quality control.
Food contaminant testing.
Forensic sample handling.
Clinical specimen collection and processing.
Ultra-trace analysis using ICP-MS and other sensitive techniques.
Advantages
Prevents false-positive or positively biased results.
Improves reliability of trace-level measurements.
Supports sample traceability and defensible laboratory records.
Blank testing helps identify contamination at different stages.
Standardized handling improves reproducibility.
Limitations
Not every contamination source can be detected by a single blank.
Blank contamination may vary between sampling events.
Cleaning procedures can introduce residues if not validated.
Contamination at concentrations close to the analyte level can be difficult to distinguish.
Blank correction is not always appropriate when contamination is variable or nonrepresentative.
Common Mistakes
Assuming a visually clean container is chemically clean.
Using one blank type to evaluate every possible contamination source.
Touching the inside of sample containers or caps.
Reusing equipment without appropriate cleaning.
Ignoring contamination from water, acids, filters, and reagents.
Failing to distinguish cross-contamination from instrument carryover.
Subtracting a blank result automatically without investigating an unusually high blank.
Prerequisites
Sample collection and preservation.
Basic laboratory safety and good laboratory practice.
Understanding of analytical blanks and measurement results.
Learning Objectives
Define contamination and sample handling.
Identify common sources of sample contamination.
Distinguish cross-contamination from instrument carryover.
Explain the purposes of field, trip, equipment, and method blanks.
Calculate blank contribution relative to a sample result.
Describe practical measures for preventing contamination.
Practice Questions
Why is contamination especially important in trace analysis?
What is the difference between a field blank and a method blank?
Explain the difference between cross-contamination and carryover.
A sample contains 25 µg/L analyte and its blank contains 1.0 µg/L. Calculate the blank contribution.
Why is a visually clean container not necessarily suitable for trace analysis?
What steps can a laboratory take to reduce contamination during sample preparation?
Key Takeaway
Contamination control is a continuous responsibility from collection to measurement. Appropriate handling practices and correctly selected blanks help identify and prevent unwanted contributions to analytical results.
References
| Title | Authors | Type | Relevance |
|---|---|---|---|
Quality Assurance of Chemical Measurements | John K. Taylor | textbook | Quality assurance, contamination, and analytical measurement reliability. |
Standard Methods for the Examination of Water and Wastewater | APHA, AWWA, and WEF | standard analytical reference | Sample collection, blanks, and contamination control. |
ISO/IEC 17025: General Requirements for the Competence of Testing and Calibration Laboratories | international standard | Laboratory competence, sample handling, and technical validity. |
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Analytical Chemistry