Sensitivity, selectivity, and specificity describe different aspects of analytical method performance. Analytical sensitivity is commonly represented by the slope of a calibration function: a larger slope means a greater change in response per concentration unit. Sensitivity is not the same as the detection limit because low-level performance also depends on noise and background variability. Selectivity describes how well a method can determine an analyte in the presence of other substances that may be present in the sample. It depends on the measurement principle, separation, sample preparation, and potential interferences. Specificity is often used to describe the ability of a method to measure a particular analyte without interference, although terminology and formal definitions can differ among analytical standards and scientific fields. In practice, complete specificity is difficult to demonstrate for complex samples, so method performance is evaluated against defined potential interferents and intended sample matrices. A method can be highly sensitive but poorly selective if interfering substances produce similar responses. Conversely, a selective method may not be sufficiently sensitive for trace-level measurement.
Sensitivity, Selectivity, and Specificity
Sensitivity describes how strongly an analytical response changes with analyte concentration. Selectivity describes the ability to measure an analyte in the presence of other components, while specificity describes a high degree of discrimination for the target analyte under defined conditions.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
S | Analytical response | Instrument-dependent |
C | Analyte concentration | mg/L, mol/L, or another defined unit |
m | Calibration slope or sensitivity | Response per concentration unit |
b | Calibration intercept | Response |
ΔS | Change in analytical response | Instrument response |
ΔC | Change in analyte concentration | Concentration unit |
Example or application
A worked example has not yet been added.
Definition
Sensitivity is the change in analytical response per unit change in analyte concentration. Selectivity is the ability of an analytical procedure to determine an analyte in the presence of other components. Specificity describes a high degree of discrimination for the analyte under defined conditions.
Purpose
To evaluate how strongly a method responds to analyte concentration and how reliably it distinguishes the analyte from other sample components.
Importance
These characteristics guide analytical method selection and validation. A useful method must provide sufficient response to the analyte and adequate discrimination from substances that could interfere with the measurement.
Key Concepts
Analytical sensitivity: change in response per concentration unit.
Instrumental sensitivity: response behaviour of the measurement system under defined conditions.
Selectivity: ability to distinguish or determine an analyte in a mixture.
Specificity: degree to which a method measures the intended analyte without relevant interference.
Interference: influence of a substance or condition that affects the analyte measurement.
Matrix effect: influence of sample components on the measured response.
Resolution: separation between neighbouring signals or chromatographic peaks.
Detection capability: ability to distinguish an analyte signal from background.
Principle
Sensitivity is evaluated from the response change associated with analyte concentration. Selectivity and specificity are evaluated by examining the method's ability to distinguish the analyte from relevant interferents and matrix components.
Working Process
Define the analyte, sample matrix, expected concentration range, and likely interfering substances.
Establish the response-concentration relationship using suitable standards.
Determine the calibration slope over the relevant working range as an indicator of sensitivity.
Assess background noise and variability separately from the slope.
Challenge the method with relevant potential interferents or representative sample matrices.
Compare analyte responses in the absence and presence of potential interferents.
Evaluate whether separation, sample preparation, or mathematical correction is needed.
Document the demonstrated selectivity or specificity under the tested conditions.
Equations
| Name | Expression | Description |
|---|---|---|
Analytical sensitivity for a linear calibration | Sensitivity = ΔS / ΔC | The change in analytical signal divided by the corresponding change in analyte concentration. For a linear calibration, this is the slope. |
Linear calibration model | S = mC + b | The slope m represents the response change per concentration unit. |
Relative interference effect | Relative effect (%) = [(S_with interferent - S_without interferent) / S_without interferent] × 100 | An illustrative comparison of response change caused by an interferent. The exact assessment should follow the analytical method and validation protocol. |
Units
Response per mg/L: sensitivity when concentration is in mg/L
Response per mol/L: sensitivity when concentration is in mol/L
mg/L or mol/L: analyte concentration
Dimensionless: relative interference effect expressed as a fraction or percentage
Examples
Method A has a calibration slope of 0.80 absorbance units per mg/L, while Method B has a slope of 0.20 absorbance units per mg/L. Method A has the greater analytical sensitivity over the compared ranges, but this alone does not prove it has a lower detection limit.
A chromatographic method separates the analyte peak from nearby matrix peaks. This separation contributes to selectivity because the analyte signal can be measured with less interference.
A spectrophotometric method may show a strong response to the analyte but also respond to a second coloured compound at the same wavelength. The method may be sensitive but insufficiently selective for that sample.
Applications
Comparing analytical methods for trace-level measurements.
Selecting wavelengths or detection conditions in spectroscopy.
Evaluating chromatographic separation of analytes and interferents.
Assessing cross-reactivity in biochemical and immunochemical assays.
Investigating matrix effects during method development and validation.
Advantages
Provides distinct criteria for evaluating analytical method performance.
Helps identify whether a method needs improved response or improved interference control.
Supports rational selection of detectors, separation methods, and sample preparation.
Helps prevent the mistaken assumption that a strong signal guarantees a reliable result.
Limitations
Sensitivity depends on the calibration range and measurement conditions.
A high calibration slope does not necessarily imply a low detection limit.
Selectivity is often matrix-dependent and must be demonstrated for relevant samples.
Specificity cannot always be established against every possible interferent.
Terminology may vary between standards, disciplines, and regulatory frameworks.
Common Mistakes
Treating sensitivity, selectivity, and specificity as synonyms.
Assuming a high calibration slope guarantees accurate measurements.
Confusing sensitivity with the limit of detection.
Ignoring matrix components that produce similar signals.
Claiming complete specificity without testing relevant potential interferents.
Evaluating selectivity using only solvent standards rather than representative samples.
Prerequisites
Calibration curves
Instrumental analytical methods
Analytical interferences
Detection and quantification limits
Basic statistics and measurement concepts
Learning Objectives
Define analytical sensitivity, selectivity, and specificity.
Explain why these characteristics are not interchangeable.
Calculate sensitivity from a linear calibration slope.
Describe how interfering substances affect selectivity.
Explain why sensitivity alone does not determine the detection limit.
Identify experiments that can evaluate method selectivity.
Practice Questions
What does the slope of a linear calibration curve indicate?
How does analytical sensitivity differ from the limit of detection?
What is meant by selectivity in analytical chemistry?
Why can a highly sensitive method still produce unreliable results in a complex matrix?
How can chromatographic separation improve selectivity?
Why should specificity claims be limited to defined analytical conditions?
Key Takeaway
Sensitivity concerns the size of the response change, while selectivity and specificity concern discrimination of the analyte from other substances. Reliable analysis requires sufficient sensitivity and adequate discrimination for the intended sample matrix.
References
| Title | Type | Url |
|---|---|---|
Harris, Quantitative Chemical Analysis | textbook | |
Skoog, Holler and Crouch, Principles of Instrumental Analysis | textbook | |
IUPAC Gold Book | terminology reference | https://goldbook.iupac.org/ |
Eurachem, The Fitness for Purpose of Analytical Methods | analytical guidance |
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Analytical Chemistry