✦ScienexySCIENCE KNOWLEDGE LIBRARY
concept · SCI-CHE-009-014

Units of Reaction Rate

The units of reaction rate express the amount of concentration change occurring per unit time and depend on the concentration and time units used.

Rate unit = concentration unit ÷ time unit; commonly mol L⁻¹ s⁻¹.

Explanation

For reactions measured using molar concentration, the common unit of reaction rate is mol L⁻¹ s⁻¹, also written as M s⁻¹. Other time units, such as minutes or hours, may be used when appropriate. In gas-phase studies, pressure change per unit time may be used as an experimental measure, while surface reactions may use rates expressed per unit area or catalyst mass. The units of a rate constant depend on the overall reaction order and are not necessarily the same as the units of reaction rate.

Variables

SymbolMeaning

mol L⁻¹

Molar concentration unit

s

Second

M

Molarity, equal to mol L⁻¹

Example or application

  • A reaction rate of 0.025 mol L⁻¹ s⁻¹ means that the normalized concentration change is 0.025 mol per litre per second.

  • A gas-phase reaction may be monitored using a pressure-change rate expressed in kPa s⁻¹.

Definition

A reaction-rate unit represents the change in a measurable concentration or amount-related quantity per unit time.

Purpose

To express reaction speeds quantitatively and ensure consistent calculations and comparisons.

Importance

Correct units prevent calculation errors, support dimensional analysis, and allow kinetic measurements from different experiments to be compared properly.

Learning Objectives

  • Identify the common units of reaction rate.

  • Convert between seconds, minutes, and hours.

  • Distinguish reaction-rate units from rate-constant units.

  • Recognize alternative rate units used in heterogeneous systems.

  • Apply dimensional analysis to rate calculations.

Key Concepts

  • Molarity

  • Concentration per time

  • Dimensional analysis

  • Pressure-change rate

  • Rate constant units

Working Principle

Reaction rate is calculated by dividing a concentration change by a time interval. The resulting unit is therefore a concentration unit divided by a time unit.

Process

  • Identify the concentration unit used in the experiment.

  • Identify the time unit.

  • Calculate the concentration change per time.

  • Write the resulting unit explicitly.

  • Convert units if comparison with another experiment is required.

Applications

  • Laboratory kinetic measurements

  • Industrial process monitoring

  • Gas-phase reaction studies

  • Heterogeneous catalysis

  • Comparing experimental rate data

Worked Example

Problem

A reaction has an average rate of 0.12 mol L⁻¹ min⁻¹. Express this rate in mol L⁻¹ s⁻¹.

Solution

  • One minute contains 60 seconds.

  • Convert the rate by dividing by 60.

  • Rate = 0.12/60 = 0.0020 mol L⁻¹ s⁻¹.

Answer

The rate is 0.0020 mol L⁻¹ s⁻¹.

Common Misconceptions

  • All reaction rates must use seconds; minutes and hours are also valid if used consistently.

  • The rate constant always has units of mol L⁻¹ s⁻¹; its units depend on the experimentally determined reaction order.

  • Pressure per time and concentration per time are always interchangeable without conditions; their relationship depends on gas behavior and experimental conditions.

Practice Questions

  • What is the common unit of reaction rate?

  • Convert 0.30 mol L⁻¹ min⁻¹ into mol L⁻¹ s⁻¹.

  • How do rate-constant units differ from reaction-rate units?

  • What unit might be used to monitor a gas-phase reaction?

  • Why is dimensional analysis important in kinetic calculations?

Key Takeaway

Reaction-rate units are obtained by dividing the relevant concentration or measurable quantity by time, with units kept consistent throughout calculations.

Prerequisites

  • Meaning of Reaction Rate

  • Molar Concentration

  • Unit Conversion

  • Basic Dimensional Analysis

Reference

  • OpenStax Chemistry 2e

  • Atkins' Physical Chemistry

  • IUPAC Gold Book

Related Topics

  • Meaning of Reaction Rate

  • Rate Laws

  • Reaction Orders

  • Rate Constants

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.

Suggest a correction or source · More in Chemical Kinetics