✦ScienexySCIENCE KNOWLEDGE LIBRARY
chemical_engineering · SCI-ENG-004-013

Chemical Engineering Units and Dimensional Consistency

A detailed introduction to physical quantities, SI units, derived engineering units, unit conversion, dimensional homogeneity and consistency checks in chemical engineering calculations.

Explanation

Introduction

Chemical engineering calculations involve physical quantities such as mass, temperature, pressure, energy, flow rate and concentration. Correct units and dimensional consistency are essential because engineering equations must represent physically meaningful relationships.

Fundamental Quantities

QuantitySymbolSIUnitUnit Symbol

Length

L

metre

m

Mass

M

kilogram

kg

Time

t

second

s

Temperature

T

kelvin

K

Amount of Substance

n

mole

mol

Electric Current

I

ampere

A

Luminous Intensity

Iv

candela

cd

Common Derived Units

QuantityFormulaSIUnit

Area

length * length

m^2

Volume

length * length * length

m^3

Velocity

length / time

m/s

Acceleration

length / time^2

m/s^2

Density

mass / volume

kg/m^3

Pressure

force / area

Pa

Energy

force * distance

J

Power

energy / time

W

Dynamic Viscosity

shear stress / velocity gradient

Pa*s

Volumetric Flow Rate

volume / time

m^3/s

Important Engineering Units

QuantityUnitsNote

Pressure

  • Pa

  • kPa

  • MPa

  • bar

Pressure may be expressed as absolute or gauge pressure; the reference must be identified.

Energy

  • J

  • kJ

  • MJ

  • kWh

Energy and power are different quantities.

Temperature

  • K

  • °C

  • °F

Temperature differences and absolute temperatures must be handled correctly.

Concentration

  • mol/m^3

  • mol/L

  • kg/m^3

  • mass percent

The concentration basis must be clearly stated.

Flow Rate

  • kg/s

  • kg/h

  • m^3/s

  • m^3/h

Mass flow rate and volumetric flow rate are not interchangeable without density information.

Dimensional Analysis

Definition

Dimensional analysis examines the fundamental dimensions of physical quantities to verify the consistency of equations and relationships.

Principle

Every additive term in a physically meaningful equation must have the same dimensions, and both sides of an equation must be dimensionally equivalent.

Example

Equation

distance = velocity * time

Dimensions

L = (L/T) * T = L

Result

The equation is dimensionally consistent.

Unit Conversions

ConversionEquivalent

1 hour

3600 seconds

1 litre

0.001 cubic metres

1 bar

100000 pascals

1 kilowatt

1000 watts

1 kilocalorie

4184 joules approximately

Worked Examples

ProblemSolutionExplanation

Convert 72 km/h to m/s.

72 * (1000/3600) = 20 m/s.

Kilometres are converted to metres and hours to seconds.

A fluid has a mass flow rate of 6 kg/s and density of 1200 kg/m^3. Calculate its volumetric flow rate.

Q = m_dot / rho = 6 / 1200 = 0.005 m^3/s.

Volumetric flow rate equals mass flow rate divided by density.

Convert 25°C into kelvin.

T(K) = 25 + 273.15 = 298.15 K.

The Celsius-to-kelvin conversion uses an offset of 273.15.

Temperature And Pressure Conventions

ConceptDescriptionRelationship

Absolute Temperature

Temperature measured relative to absolute zero, normally expressed in kelvin for thermodynamic equations.

Gauge Pressure

Pressure measured relative to the local atmospheric pressure.

Absolute Pressure

Pressure measured relative to a perfect vacuum.

Absolute pressure = Gauge pressure + Atmospheric pressure

Common Errors

  • Mixing kilograms with grams without conversion.

  • Using Celsius where absolute temperature is required.

  • Confusing mass flow rate with volumetric flow rate.

  • Confusing pressure expressed in gauge units with absolute pressure.

  • Adding quantities with incompatible dimensions.

  • Using inconsistent time units in flow calculations.

Importance

Correct unit handling prevents major calculation errors and is essential for engineering communication, equipment design and process safety.

Practice

  • List the seven SI base quantities.

  • Convert 3.6 m^3/h into m^3/s.

  • Convert 150 kPa into pascals.

  • Explain the difference between absolute and gauge pressure.

  • Check the dimensional consistency of the equation for density.

Example or application

A worked example has not yet been added.

Importance

This topic develops the measurement and calculation discipline required throughout chemical engineering.

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • The International System of Units (SI) by BIPM
  • NIST Guide to the SI
  • Elementary Principles of Chemical Processes by Felder, Rousseau and Bullard

Suggest a correction or source · More in Chemical Engineering