✦ScienexySCIENCE KNOWLEDGE LIBRARY
topic · SCI-PHY-006-015

SI Units and Dimensions of Rotational Quantities

Rotational mechanics uses SI units and dimensional formulas to measure angular displacement, angular velocity, angular acceleration, torque, moment of inertia, angular momentum, rotational energy, and power. Dimensional analysis helps verify equations and distinguish quantities that may have similar units but different physical meanings.

Explanation

Physical quantities in rotational mechanics are expressed using the International System of Units (SI). Angular displacement is measured in radians, angular velocity in radians per second, and angular acceleration in radians per second squared. Since the radian is defined as the ratio of arc length to radius, it is dimensionless in dimensional analysis, even though it is retained as a named unit to clarify angular meaning. Torque is measured in newton metres (N·m), while moment of inertia is measured in kilogram square metres (kg·m²). Angular momentum is measured in kilogram square metres per second (kg·m²/s), and rotational energy is measured in joules (J). Rotational power is measured in watts (W), equivalent to joules per second. Dimensional formulas express physical quantities in terms of fundamental dimensions such as mass [M], length [L], and time [T]. Torque and energy both have the dimensions [M L² T⁻²], but they are different physical quantities: torque is a vector moment of force, whereas energy is a scalar. Their SI units are written differently to preserve this distinction: N·m for torque and J for energy. Dimensional analysis can check whether the dimensions on both sides of an equation are consistent. However, dimensional consistency alone cannot prove that an equation is physically correct or determine numerical constants.

Example or application

Torque is measured in N·m. Since one newton is kg·m/s², the dimensional formula of torque is kg·m²/s², or [M L² T⁻²]. This is the same dimensional formula as energy, although torque and energy are physically different quantities.

Definition

SI units are internationally standardized units used to express physical measurements, while dimensional formulas represent physical quantities in terms of fundamental dimensions such as mass, length, and time.

Purpose

The purpose of units and dimensional analysis is to provide consistent measurement, verify mathematical relationships, convert between measurement systems, and prevent errors in rotational mechanics.

Importance

Correct units and dimensions are essential for accurate calculations, engineering communication, experimental measurements, and checking rotational equations. They also help distinguish quantities with similar dimensions but different physical meanings.

Si Base Units

QuantitySymbolSIUnitUnit SymbolDimension

Mass

m

kilogram

kg

[M]

Length

l

metre

m

[L]

Time

t

second

s

[T]

Rotational Quantities

QuantitySymbolSIUnitUnit SymbolDimensionDimensional Formula

Angular displacement

θ

radian

rad

dimensionless

[1]

Angular velocity

ω

radian per second

rad/s

inverse time

[T⁻¹]

Angular acceleration

α

radian per second squared

rad/s²

inverse time squared

[T⁻²]

Torque

τ

newton metre

N·m

mass × length squared / time squared

[M L² T⁻²]

Moment of inertia

I

kilogram square metre

kg·m²

mass × length squared

[M L²]

Angular momentum

L

kilogram square metre per second

kg·m²/s

mass × length squared / time

[M L² T⁻¹]

Rotational kinetic energy

K_rot

joule

J

mass × length squared / time squared

[M L² T⁻²]

Rotational power

P

watt

W

mass × length squared / time cubed

[M L² T⁻³]

Derived SIUnits

QuantityUnitSymbolBase Unit Expression

Force

newton

N

1 N = 1 kg·m/s²

Torque

newton metre

N·m

1 N·m = 1 kg·m²/s²

Energy

joule

J

1 J = 1 kg·m²/s²

Power

watt

W

1 W = 1 J/s = 1 kg·m²/s³

Dimensional Derivations

QuantityEquationDerivation

Angular velocity

ω = θ/t

Angle is dimensionless, so angular velocity has dimension [T⁻¹].

Angular acceleration

α = ω/t

Angular velocity has dimension [T⁻¹], so angular acceleration has dimension [T⁻²].

Torque

τ = rF

Length multiplied by force gives [L][M L T⁻²] = [M L² T⁻²].

Moment of inertia

I = Σmr²

Mass multiplied by squared distance gives [M L²].

Angular momentum

L = r × p

Length multiplied by linear momentum gives [L][M L T⁻¹] = [M L² T⁻¹].

Rotational kinetic energy

K_rot = 1/2 Iω²

Moment of inertia multiplied by angular velocity squared gives [M L²][T⁻²] = [M L² T⁻²].

Rotational power

P = τω

Torque multiplied by angular velocity gives [M L² T⁻²][T⁻¹] = [M L² T⁻³].

Other Units And Conversions

QuantityConversion

Angular displacement

1 revolution = 2π rad = 360°

Angular velocity

1 revolution per minute = 2π/60 rad/s

Energy

1 kWh = 3.6 × 10⁶ J

Energy

1 eV ≈ 1.602176634 × 10⁻¹⁹ J

Power

1 mechanical horsepower ≈ 745.7 W

Dimensional Analysis

Definition

Dimensional analysis is the method of expressing physical quantities in terms of fundamental dimensions and checking the dimensional consistency of equations.

Uses

  • Checking whether both sides of an equation have the same dimensions.

  • Identifying possible errors in derived equations.

  • Deriving the form of relationships between physical quantities.

  • Converting quantities between unit systems.

  • Determining the dimensions of unknown physical constants.

Limitations

  • It cannot determine dimensionless numerical constants.

  • It cannot prove that a dimensionally consistent equation is physically correct.

  • It cannot distinguish all different physical quantities that share the same dimensions.

  • It does not replace experimental verification or a physical derivation.

Important Unit Distinctions

  • Torque and energy have the same dimensions, but torque is measured in N·m and energy in J to emphasize their different physical meanings.

  • The radian is dimensionless in dimensional analysis but is retained in unit expressions to identify angular quantities.

  • Angular velocity in rad/s is not the same physical quantity as frequency in hertz, even though both have the dimension [T⁻¹]. They are related by ω = 2πf for periodic rotation.

  • Moment of inertia has units of kg·m², not kg·m.

  • Rotational power is measured in watts, not joules.

Worked Example

Problem

A rotating shaft experiences a torque of 12 N·m and has angular velocity 5 rad/s. Find the rotational power delivered by the torque when torque and angular velocity are aligned.

Given

  • τ = 12 N·m

  • ω = 5 rad/s

Equation

P = τω

Solution

P = 12 × 5 = 60 N·m/s = 60 J/s = 60 W.

Answer

The rotational power is 60 W.

Common Misconceptions

  • Torque and energy have the same dimensions but are not the same physical quantity.

  • The radian is dimensionless in dimensional analysis, but it is still useful to write rad when expressing angular measurements.

  • Angular velocity and frequency have the same dimensions but differ by a factor of 2π for periodic motion.

  • Moment of inertia is measured in kg·m², not simply kilograms.

  • Dimensional consistency is necessary for a valid physical equation but is not sufficient to prove that the equation is correct.

Learning Objectives

  • Identify SI units of important rotational quantities.

  • Derive dimensional formulas from defining equations.

  • Distinguish torque from energy despite their shared dimensions.

  • Convert between angular units and common rotational units.

  • Use dimensional analysis to check equations.

Key Takeaway

Correct units and dimensions make rotational calculations consistent. Dimensional analysis is a powerful checking tool, but physical reasoning and experimental evidence are also required.

Prerequisites

  • SI base units

  • Derived units

  • Dimensional formulas

  • Angular motion

  • Torque

  • Moment of inertia

  • Basic algebra

Related Topics

  • SCI-PHY-006-001

  • SCI-PHY-006-004

  • SCI-PHY-006-013

  • SCI-PHY-006-014

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

Suggest a correction or source · More in Rotational Mechanics