✦ScienexySCIENCE KNOWLEDGE LIBRARY
reference · SCI-REF-002-064

Molar Volume of an Ideal Gas

The molar volume of an ideal gas is the volume occupied by one mole of gas under specified temperature and pressure conditions. Unlike a universal fundamental constant, it is a condition-dependent reference quantity calculated from the ideal gas law.

Vₘ = V/n = RT/P

Explanation

Molar volume describes the volume occupied per mole of a substance. For an ideal gas, it follows directly from the equation of state PV = nRT. Dividing the gas volume by the amount of substance gives Vₘ = V/n = RT/P. Therefore, the molar volume is not one fixed value: it changes with absolute temperature and pressure. At a specified reference temperature and pressure, it becomes a useful comparison quantity. For example, at 273.15 K and 1 atm, the ideal-gas molar volume is approximately 22.414 L·mol⁻¹. At 273.15 K and 1 bar, it is approximately 22.711 L·mol⁻¹. At 298.15 K and 1 bar, it is approximately 24.790 L·mol⁻¹. These differences demonstrate why temperature and pressure must always accompany a quoted molar volume. Real gases may deviate from the ideal-gas prediction, particularly at high pressure and low temperature.

Variables

SymbolMeaningUnitValue

Vₘ

Molar volume

m³·mol⁻¹

V

Total volume of the gas

m³

n

Amount of gas

mol

R

Universal gas constant

J·mol⁻¹·K⁻¹

8.31446261815324 J·mol⁻¹·K⁻¹

T

Absolute thermodynamic temperature

K

P

Absolute pressure

Pa

Example or application

A worked example has not yet been added.

Definition

The molar volume of a gas is the volume occupied per mole of gas under specified temperature and pressure conditions.

Purpose

To convert between the amount of an ideal gas and its volume when temperature and pressure are known.

Importance

Molar volume is useful in gas stoichiometry, laboratory measurements, chemical engineering, environmental science, and thermodynamic calculations. It allows gas volumes to be compared meaningfully when their measurement conditions are specified.

Reference Conditions

ConditionIdeal Molar VolumeDescription

273.15 K and 1 atm (101,325 Pa)

Approximately 22.414 L·mol⁻¹

A traditional standard-temperature-and-pressure convention.

273.15 K and 1 bar (100,000 Pa)

Approximately 22.711 L·mol⁻¹

A common IUPAC standard-pressure reference at 0 °C.

298.15 K and 1 bar

Approximately 24.790 L·mol⁻¹

A commonly used room-temperature reference condition.

Physical Interpretation

For a fixed amount of ideal gas, volume increases in direct proportion to absolute temperature at constant pressure and decreases in inverse proportion to pressure at constant temperature. Molar volume expresses these relationships on a per-mole basis.

Worked Example

Problem

Calculate the molar volume of an ideal gas at 300 K and 100 kPa.

Solution

  • Use Vₘ = RT/P.

  • R = 8.314462618 J·mol⁻¹·K⁻¹.

  • T = 300 K and P = 100,000 Pa.

  • Vₘ = (8.314462618 × 300)/100,000 m³·mol⁻¹.

  • Vₘ ≈ 0.0249434 m³·mol⁻¹.

Answer

The molar volume is approximately 24.94 L·mol⁻¹.

Real Gas Corrections

Description

Real gases do not always obey PV = nRT exactly. Their molar volume can be described using a compressibility factor.

Formula

Vₘ = ZRT/P

Explanation

Z is the dimensionless compressibility factor. For an ideal gas, Z = 1. Deviations from unity indicate non-ideal behaviour.

Conditions And Limitations

  • Temperature must be expressed in kelvin and pressure in pascals when using SI units.

  • Pressure must be absolute pressure, not gauge pressure.

  • The ideal-gas expression assumes negligible molecular volume and negligible intermolecular forces.

  • Real-gas deviations become important near condensation, at high pressures, and at sufficiently low temperatures.

  • A quoted molar volume is incomplete unless its temperature, pressure, and ideal-gas or real-gas basis are stated.

Common Misconceptions

  • The value 22.4 L·mol⁻¹ is not valid under every temperature and pressure condition.

  • Standard temperature and pressure conventions are not interchangeable unless their exact pressure and temperature definitions match.

  • Molar volume is not a universal fundamental constant like the speed of light.

Related Topics

  • Universal Gas Constant

  • Avogadro Constant

  • Ideal Gas Law

  • Standard-State Reference Quantities

  • Compressibility Factor

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • IUPAC Gold Book — Molar volume and standard conditions.
  • Atkins' Physical Chemistry — Gases and equations of state.
  • NIST — Chemistry WebBook and thermodynamic reference data.

Suggest a correction or source · More in Physical Constants