✦ScienexySCIENCE KNOWLEDGE LIBRARY
reference · SCI-REF-002-074

Thermal Conductivity of Materials

Thermal conductivity quantifies a material's ability to conduct heat through a temperature gradient. It is a condition-dependent transport property used in heat transfer, thermal engineering, insulation design, electronics cooling, and materials science.

q = −k∇T

Explanation

Heat is transferred through a material when a temperature difference exists. Thermal conductivity measures how effectively the material transports thermal energy by conduction. In a simple isotropic material under steady or locally approximated conditions, Fourier's law relates heat flux to the temperature gradient. A material with high thermal conductivity transfers heat readily, whereas a material with low thermal conductivity acts as a better thermal insulator. Heat conduction occurs through different microscopic mechanisms depending on the material. In metals, mobile electrons often carry a major fraction of thermal energy. In electrically insulating crystals, lattice vibrations or phonons are important. In gases, molecular collisions transfer energy, while liquids involve molecular motion and interactions. Thermal conductivity can vary with temperature, pressure, composition, porosity, crystal direction, and microstructure. In anisotropic materials, it is described by a tensor rather than one scalar value.

Variables

SymbolMeaningUnit

q

Heat flux, meaning heat-transfer rate per unit area

W·m⁻²

k

Thermal conductivity

W·m⁻¹·K⁻¹

∇T

Temperature gradient

K·m⁻¹

Example or application

A worked example has not yet been added.

Definition

Thermal conductivity is the proportionality property relating conductive heat flux to the negative temperature gradient in a material.

Purpose

To quantify the ability of a material to conduct thermal energy and predict temperature distributions and heat-transfer rates.

Importance

Thermal conductivity is critical in insulation, heat exchangers, building materials, electronic-device cooling, engines, energy systems, thermal protection, and industrial manufacturing.

Microscopic Mechanisms

MechanismDescription

Electronic conduction

In metals and some other conductive materials, mobile electrons transport thermal energy through the material.

Lattice or phonon conduction

In non-metallic crystalline solids, energy is transported by collective lattice vibrations called phonons.

Molecular conduction

In gases and liquids, molecular motion and collisions contribute to energy transfer.

Radiative contribution

In some transparent or high-temperature materials, internal thermal radiation can contribute to effective heat transfer. This contribution is often treated separately or incorporated into an effective conductivity.

Typical Material Values

MaterialApproximate Thermal ConductivityNote

Air near room temperature

0.026 W·m⁻¹·K⁻¹

Depends on temperature, pressure, and humidity.

Wood

0.1–0.2 W·m⁻¹·K⁻¹

Depends strongly on moisture, grain direction, and species.

Glass

Approximately 0.8–1.2 W·m⁻¹·K⁻¹

Varies with glass composition and temperature.

Stainless steel

Approximately 14–20 W·m⁻¹·K⁻¹

Depends on grade and temperature.

Copper

Approximately 390–400 W·m⁻¹·K⁻¹

High-purity copper generally has very high thermal conductivity near room temperature.

Diamond

Can exceed 1,000 W·m⁻¹·K⁻¹

Highly dependent on purity, crystal quality, and temperature.

Anisotropic Conductivity

Description

In anisotropic materials, heat flux does not necessarily point exactly opposite to the temperature gradient. Thermal conductivity is represented by a second-rank tensor.

Formula

qᵢ = −Σⱼ kᵢⱼ(∂T/∂xⱼ)

Note

The scalar Fourier law is recovered for isotropic materials.

Worked Example

Problem

A wall has thermal conductivity 0.8 W·m⁻¹·K⁻¹, thickness 0.20 m, and area 10 m². The temperature difference across it is 20 K. Estimate the steady heat-transfer rate assuming one-dimensional conduction and no additional thermal resistance.

Solution

  • For a plane wall, the heat-transfer rate is Q̇ = kAΔT/L.

  • Substitute k = 0.8, A = 10, ΔT = 20, and L = 0.20.

  • Q̇ = (0.8 × 10 × 20)/0.20 W.

  • Q̇ = 800 W.

Answer

The estimated steady heat-transfer rate is 800 W.

Measurement Methods

  • Guarded hot-plate methods measure steady-state heat flow through flat specimens.

  • Heat-flow-meter methods determine conductivity from measured heat flux and temperature difference.

  • Laser-flash analysis measures thermal diffusivity, which can be combined with density and specific heat capacity to obtain thermal conductivity.

  • Transient hot-wire methods are commonly used for suitable fluids and some insulating materials.

  • Comparative methods use reference materials with known thermal properties.

Conditions And Limitations

  • Thermal conductivity depends on temperature and may vary substantially across a wide temperature range.

  • The simple Fourier relation assumes a continuum description and local thermal equilibrium.

  • Anisotropic materials require directional or tensor conductivity data.

  • Porosity, cracks, moisture, interfaces, and impurities can strongly affect effective thermal conductivity.

  • At very small length scales, classical Fourier conduction may become insufficient because of nonlocal or ballistic transport effects.

  • Contact resistance and radiation can affect experimental measurements and must be accounted for when relevant.

Common Misconceptions

  • Thermal conductivity is not the same as thermal diffusivity.

  • A material with high thermal conductivity is not necessarily a good thermal insulator.

  • Thermal conductivity does not directly describe how much energy is required to raise a material's temperature.

  • A quoted thermal conductivity without temperature and material-direction information may be insufficient for engineering design.

Related Topics

  • Specific Heat Capacity and Heat Capacity

  • Material Density and Specific Volume

  • Coefficients of Thermal Expansion

  • Molecular Diffusion and Transport Coefficients

  • Thermal Diffusivity

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Incropera et al. — Fundamentals of Heat and Mass Transfer.
  • Callister and Rethwisch — Materials Science and Engineering: An Introduction.
  • NIST — Thermophysical Properties of Materials.

Suggest a correction or source · More in Physical Constants