Measurement methods can be classified according to how the value of the measurand is obtained. In direct measurement, the measurement system provides an indication that is directly related to the quantity being measured through the instrument's measurement principle and calibration. In indirect measurement, the target quantity is calculated from measurements of other quantities using a mathematical relationship or measurement model.
A direct measurement does not mean that no interpretation, calibration or correction is involved. An instrument indication is rarely identical to the final measurement result without further consideration. For example, a ruler may directly indicate a length, but the result can still depend on alignment, scale calibration, temperature, contact conditions and reading resolution.
A direct measurement is commonly performed by comparing the measurand with a reference or by using an instrument whose response is calibrated in units of the measurand. A balance provides an indication related to mass through its operating principle and calibration. A thermometer provides an indication related to temperature through a calibrated sensor response. A voltmeter provides an indication of potential difference based on its electrical measurement system.
In indirect measurement, the target quantity is obtained from other measured quantities. Density can be calculated from mass and volume using ρ = m/V. Average speed can be calculated from distance and elapsed time using v = s/t. Electrical resistance can be determined from measured voltage and current using R = V/I, provided the relevant electrical conditions and model assumptions are satisfied.
Indirect measurement is essential when the target quantity cannot be measured conveniently or directly with sufficient reliability. Many quantities in physics, chemistry, engineering and astronomy are determined through models involving several measured inputs. For example, the acceleration of a moving object may be determined from position measurements collected over time and processed using a suitable motion model.
Every indirect measurement requires a measurement model. The model describes the relationship between the measurand and the input quantities. In a general form, y = f(x₁, x₂, ..., xₙ), where y is the output quantity and xᵢ are measured input quantities. The model may also contain constants, correction factors or environmental parameters.
The quality of an indirect measurement depends on the quality of the input measurements and the validity of the model. If any input value has uncertainty, that uncertainty can contribute to the uncertainty of the calculated result. The mathematical relationship may also introduce correlations between inputs or require corrections for systematic effects.
Direct and indirect methods may be used together. A measuring instrument may directly indicate one quantity while internally calculating another. A digital multimeter, for example, may measure electrical signals and process them to display a derived quantity. In a laboratory, a researcher may directly measure mass and volume and then calculate density indirectly.
The distinction between direct and indirect measurement is based on the measurement method, not simply on whether a display shows a number. An instrument that displays a calculated result may still rely on indirect measurement internally. Similarly, a measurement described as direct may require substantial calibration and data processing.
A suitable method is selected according to the measurand, required measurement range, expected uncertainty, available reference standards, environmental conditions and practical constraints. Direct methods are often simpler to interpret, while indirect methods can provide access to quantities that are difficult or impossible to determine through a direct comparison.
Direct and Indirect Measurement
Direct measurement obtains a quantity value from a measurement system that responds to the measurand through a defined measurement procedure. Indirect measurement determines a quantity using values of other quantities and a mathematical or physical model. Both methods are fundamental to scientific experimentation and practical measurement.
For a direct indication: y = g(I), where I is the instrument indication and g represents applicable calibration or correction. For an indirect measurement: y = f(x₁, x₂, ..., xₙ), where xᵢ are measured input quantities.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
y | The measurement result or measurand value. | Depends on the quantity. |
I | Instrument indication. | Depends on the instrument. |
g | Calibration or correction relationship connecting an indication to the measurement result. | Depends on the relationship. |
f | Measurement model relating input quantities to the output quantity. | Depends on the model. |
xᵢ | Measured input quantities used to determine the measurand. | Depends on each input. |
Example or application
A worked example has not yet been added.
Definition
Direct measurement is a measurement method in which the value of the measurand is obtained from an instrument indication or comparison directly related to that quantity. Indirect measurement determines the measurand from measurements of other quantities through a defined measurement model.
Purpose
To explain how measurement results are obtained directly or calculated from other measured quantities, and to establish the principles governing each approach.
Importance
This distinction helps in selecting suitable measurement procedures, understanding the role of mathematical models and evaluating how input measurement uncertainties influence calculated results.
Direct Measurement Examples
| Quantity | Instrument | Method | Result |
|---|---|---|---|
Length | Ruler or calibrated length-measuring instrument. | Compare the object's length with the instrument scale. | A length indication expressed in units such as metres or centimetres. |
Mass | Calibrated balance. | Obtain the balance indication using its measurement principle. | A mass value expressed in kilograms or grams. |
Temperature | Calibrated thermometer. | Obtain a temperature-related sensor indication and apply the instrument's calibrated relationship. | A temperature value expressed in kelvin or an accepted temperature scale. |
Electric potential difference | Voltmeter. | Connect the instrument appropriately and obtain the potential difference indication. | A voltage value expressed in volts. |
Indirect Measurement Examples
| Quantity | Input Quantities | Formula | Description |
|---|---|---|---|
Density |
| ρ = m/V | Density is calculated from measured mass and volume. |
Average speed |
| v̄ = s/Δt | Average speed is calculated from total distance and elapsed time. |
Electrical resistance |
| R = V/I | Resistance is determined using Ohm's law under appropriate conditions. |
Acceleration |
| a = d²x/dt² | Acceleration may be inferred from position measurements and an appropriate time-dependent model. |
Volume of a cylinder |
| V = πr²h | Volume is calculated from measured geometric dimensions. |
Measurement Model Requirements
Clearly define the measurand and all relevant input quantities.
Specify the mathematical or physical relationship between the inputs and the measurand.
Identify constants, correction factors and assumptions.
Use appropriate units and ensure dimensional consistency.
Evaluate the uncertainty of each important input quantity.
Consider correlations between input quantities when relevant.
Check whether the model is valid under the actual measurement conditions.
Report the result and uncertainty using appropriate conventions.
Worked Examples
Title
Direct measurement of length
Method
A calibrated measuring instrument is used to compare the length of an object with its scale.
Indication
12.4 cm
Result
0.124 m
Interpretation
The length is obtained directly from the instrument indication, with any necessary corrections and uncertainty considered.
Title
Indirect measurement of density
Given
Mass = 200 g = 0.200 kg
Volume = 100 cm³ = 1.00 × 10⁻⁴ m³
Formula
ρ = m/V
Calculation
ρ = 0.200 kg / 1.00 × 10⁻⁴ m³ = 2000 kg/m³
Answer
2000 kg/m³
Interpretation
Density is calculated indirectly using measured mass and volume.
Title
Indirect measurement of electrical resistance
Given
Potential difference = 12 V
Current = 2 A
Formula
R = V/I
Calculation
R = 12 V / 2 A = 6 Ω
Answer
6 Ω
Interpretation
Resistance is calculated from measured voltage and current, assuming the relationship is valid for the component and measurement conditions.
Uncertainty Considerations
Direct measurements can contain uncertainty from instrument calibration, resolution, repeatability and environmental effects.
Indirect measurements inherit uncertainty from their input quantities.
The sensitivity of the output to each input determines how strongly that input contributes to output uncertainty.
Correlations between inputs may affect the combined uncertainty.
Model limitations and neglected effects may contribute additional uncertainty.
Corrections should be applied only when their basis and uncertainty are understood.
Applications
Laboratory experiments.
Industrial dimensional inspection.
Material property determination.
Electrical and electronic testing.
Mechanical engineering calculations.
Scientific sensor systems.
Astronomical parameter estimation.
Environmental measurement and monitoring.
Limitations
Direct measurement is not necessarily more accurate than indirect measurement.
Indirect measurement depends on the validity of its mathematical or physical model.
A direct instrument indication may require calibration and correction.
Uncertainty can increase when several input quantities contribute to an indirect result.
Some measurands cannot be obtained using a simple direct measurement method.
Common Misconceptions
Direct measurement does not mean measurement without calibration or uncertainty.
Indirect measurement is not inherently less reliable than direct measurement.
A digital instrument displaying a calculated quantity may use an indirect measurement model internally.
A measurement model must be scientifically valid, not merely mathematically convenient.
The uncertainties of input quantities must be considered in calculated results.
Related Concepts
Measurement Process
Measurement Models
Measuring Instruments
Measurement Uncertainty
Calibration
Uncertainty Propagation
Reference
International Vocabulary of Metrology (VIM), JCGM 200:2012.
Evaluation of Measurement Data — Guide to the Expression of Uncertainty in Measurement (GUM), JCGM 100:2008.
The International System of Units (SI Brochure), 9th edition, BIPM.
Related Topic
SCI-REF-003-001
SCI-REF-003-004
SCI-REF-003-009
SCI-REF-003-010
SCI-REF-003-059
SCI-REF-003-086
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Units & Measurement