A physical quantity is expressed quantitatively by combining a numerical value with a unit. For example, 12 m represents a length whose numerical value is 12 when expressed in metres. The numerical value depends on the selected unit, but the physical quantity itself does not change when the unit is changed correctly.
The general representation of a quantity value is Q = {Q}[Q], where Q is the quantity, {Q} is its numerical value and [Q] is its unit. For example, 2.5 m = 250 cm = 0.0025 km. These expressions represent the same length using different numerical values and units.
A unit is a reference used to express the magnitude of a quantity of a particular kind. Units are not arbitrary labels attached to numbers; they form part of a defined measurement system. In the SI, base and derived units are constructed within a coherent system, allowing quantities to be expressed consistently across scientific disciplines.
The numerical value of a quantity changes inversely with the size of the chosen unit. If a larger unit is selected, fewer units are required to represent the same quantity. If a smaller unit is selected, a larger numerical value is required. This relationship is the basis of unit conversion.
A quantity value should be distinguished from a measurement result. The value is the numerical expression of the quantity, while a measurement result is the information obtained from the measurement process and attributed to the measurand. Depending on the context, a measurement result may include one or more quantity values, uncertainty information, measurement conditions and supporting documentation.
A measurement result is not always a single exact number. In practical measurement, uncertainty is associated with the result because the available information does not determine the measurand value perfectly. A result may therefore be expressed as an estimate accompanied by standard uncertainty or expanded uncertainty. For example, a length might be reported as (12.34 ± 0.02) cm, provided the meaning of the uncertainty and its coverage information are stated appropriately.
The plus-minus notation alone is not sufficient to define uncertainty completely. A report should indicate whether the uncertainty is standard uncertainty, expanded uncertainty or another specified interval, and should provide a coverage factor or probability interpretation where appropriate. The number of reported digits should also be consistent with the uncertainty and the intended use of the result.
Units must be written using standardized symbols and formatting rules. Unit symbols are mathematical entities, not abbreviations. They are generally not pluralized and are not followed by a full stop unless they occur at the end of a sentence. A space is normally placed between a numerical value and a unit symbol, such as 25 kg, 12 m and 300 K. Exceptions include certain angle symbols, such as 30°, where the degree symbol is attached to the numerical value.
Unit symbols are case-sensitive. For example, m represents metre, while M is the SI prefix mega. The symbol for kilogram is kg, not Kg. The symbol for the newton is N, while the symbol for the second is s. Correct capitalization is essential because changing a symbol's case may change its meaning.
Compound units are formed using multiplication, division and powers. Examples include m/s, kg/m³, N·m and J/(kg·K). The centred dot is often used to indicate multiplication between unit symbols when necessary for clarity. Negative exponents may be used to represent division, such as m·s⁻¹ for metre per second.
The distinction between quantity symbols and unit symbols is important. Quantity symbols are usually italicized in mathematical writing, whereas unit symbols are written in upright roman type. For example, m may represent mass as a quantity symbol in an equation, while m as a unit symbol represents metre. Context and typography help distinguish them.
Numerical results must also be reported with appropriate rounding and significant digits. The displayed digits should not imply more information than the measurement supports. However, significant figures are not a complete substitute for uncertainty evaluation. A result with many digits may still be inaccurate, while a carefully rounded result can communicate the measurement more honestly.
For derived quantities, the unit follows from the mathematical relationship. If velocity is distance divided by time, its SI unit is m/s. If force is mass multiplied by acceleration, its SI unit is kg·m·s⁻², which is called the newton. Unit analysis can therefore be used to check the consistency of calculations.
A well-reported measurement result should identify the measurand, numerical value, unit, uncertainty where relevant, measurement method and conditions necessary for interpretation. In high-quality scientific and industrial work, calibration and traceability information may also be required. This allows others to understand, compare and evaluate the result.
Numerical Values, Units and Measurement Results
A physical quantity value is expressed through a numerical value and a unit, while a complete measurement result may also require uncertainty, measurement conditions, method and other relevant information. Understanding the relationship between quantity values, unit selection, numerical representation and reporting conventions is essential for accurate scientific communication.
Q = {Q}[Q]. For unit conversion: {Q}₁[Q]₁ = {Q}₂[Q]₂. Therefore, {Q}₂ = {Q}₁ × ([Q]₁/[Q]₂), where the unit ratio is expressed consistently.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
Q | The physical quantity. | Depends on the quantity. |
{Q} | Numerical value of the quantity in a selected unit. | Dimensionless. |
[Q] | The unit selected to express the quantity. | Relevant measurement unit. |
{Q}₁ | Numerical value in the first unit. | Dimensionless. |
{Q}₂ | Numerical value in the second unit. | Dimensionless. |
u | Standard measurement uncertainty when used with an appropriate quantity. | Same as the associated measured quantity. |
Example or application
A worked example has not yet been added.
Definition
A quantity value is the expression of a quantity as a number and a reference. A measurement result is the set of quantity values being attributed to a measurand, together with relevant information such as uncertainty and conditions needed for interpretation.
Purpose
To explain how physical quantity values are represented, how numerical values depend on unit selection and how measurement results should be expressed and reported.
Importance
Correct numerical and unit representation prevents ambiguity, supports dimensional consistency, enables reliable conversion and allows scientific results to be communicated and compared internationally.
Quantity Value Structure
| Component | Description |
|---|---|
Physical quantity | The property being expressed, such as length, mass or temperature. |
Numerical value | The number representing the magnitude in the selected unit. |
Unit | The reference scale used to express the quantity. |
Uncertainty | Information characterizing the dispersion of values that could reasonably be attributed to the measurand. |
Measurement conditions | Conditions required to understand the result, such as temperature, pressure, location and time. |
Method and traceability information | Information describing how the result was obtained and, where relevant, how it is linked to recognized references. |
Unit Writing Rules
| Rule | Description | Correct | Incorrect |
|---|---|---|---|
Space between value and unit | A space is normally placed between a numerical value and its unit symbol. | 25 kg | 25kg |
Unit symbols are not pluralized | The same unit symbol is used for singular and plural values. | 5 m | 5 ms |
Unit symbols are case-sensitive | Capitalization must follow the accepted symbol. | 5 N | 5 n |
No full stop after a unit symbol | A unit symbol does not receive a period unless it occurs at the end of a sentence. | The length is 5 m. | The length is 5 m. |
Compound units require clear mathematical formatting | Use multiplication dots, negative powers or parentheses to avoid ambiguity. | kg·m·s⁻² | kg m/s s |
Prefix and unit symbols are combined without a space | An SI prefix symbol is attached directly to its unit symbol. | km | k m |
Quantity symbols and unit symbols have different typographic conventions | Quantity symbols are generally italic, while unit symbols are upright. | m = 5 kg, where m denotes mass. | Using the same typographic treatment without context in technical writing. |
Unit Representation Examples
| Quantity | Quantity Symbol | Unit | Unit Symbol | Example |
|---|---|---|---|---|
Length | l | metre | m | 2.5 m |
Mass | m | kilogram | kg | 3.2 kg |
Time interval | Δt | second | s | 15 s |
Velocity | v | metre per second | m/s | 12 m/s |
Force | F | newton | N | 25 N |
Pressure | p | pascal | Pa | 101325 Pa |
Measurement Result Reporting
Identify the measurand clearly.
Provide the numerical value and unit.
Include measurement uncertainty when required or relevant.
State the uncertainty type and coverage information where appropriate.
Report the measurement method or procedure when necessary.
Specify relevant environmental and experimental conditions.
Include corrections applied to the raw indications when relevant.
Provide calibration or traceability information when required.
Use appropriate significant digits and rounding.
Avoid implying greater certainty than the measurement supports.
Worked Examples
Title
Changing the numerical value by changing the unit
Given
Length = 2.5 m
Conversion
1 m = 100 cm
Calculation
2.5 m × 100 cm/m = 250 cm
Answer
2.5 m = 250 cm
Interpretation
The physical length remains unchanged while its numerical value changes.
Title
Expressing a measurement result with uncertainty
Given
Estimated length = 12.34 cm
Standard uncertainty = 0.02 cm
Result
(12.34 ± 0.02) cm
Interpretation
The result is reported with an associated standard uncertainty. The plus-minus notation should be identified explicitly as standard uncertainty rather than assumed to represent a particular confidence interval.
Title
Writing a derived unit
Given
Mass = 10 kg
Acceleration = 2 m/s²
Formula
F = ma
Calculation
F = 10 × 2 = 20 kg·m·s⁻²
Answer
20 N
Interpretation
The unit kg·m·s⁻² is equivalent to the named SI derived unit newton.
Title
Recognizing a unit-writing error
Incorrect
The sample mass is 5 Kgs.
Correct
The sample mass is 5 kg.
Interpretation
The SI unit symbol kg is case-sensitive and is not pluralized.
Limitations
A numerical value without a clearly identified unit may be ambiguous.
A value and unit alone may not fully describe a measurement result.
Uncertainty notation can be misleading if the uncertainty type and coverage information are omitted.
Rounding may discard information if performed before calculations are completed.
The number of displayed digits does not independently establish measurement accuracy.
Different measurement conditions can make apparently similar results non-comparable.
Common Misconceptions
The number and the unit together express the quantity value.
Changing units does not change the physical quantity.
The unit symbol kg is not an abbreviation that can be pluralized.
A measurement result may need uncertainty and conditions in addition to a numerical value and unit.
The symbol for metre is m, while the symbol for mass as a quantity is commonly m; context and typography distinguish them.
More decimal places do not automatically indicate a more accurate measurement.
Related Concepts
Measurement
Physical Quantities
SI Unit Symbols
Unit Conversion
Significant Figures
Measurement Uncertainty
Measurement Reporting
Reference
The International System of Units (SI Brochure), 9th edition, BIPM.
International Vocabulary of Metrology (VIM), JCGM 200:2012.
Evaluation of Measurement Data — Guide to the Expression of Uncertainty in Measurement (GUM), JCGM 100:2008.
ISO 80000 series, Quantities and Units.
Related Topic
SCI-REF-003-001
SCI-REF-003-004
SCI-REF-003-005
SCI-REF-003-009
SCI-REF-003-013
SCI-REF-003-015
SCI-REF-003-040
SCI-REF-003-049
SCI-REF-003-079
SCI-REF-003-088
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Units & Measurement