✦ScienexySCIENCE KNOWLEDGE LIBRARY
reference · SCI-REF-003-046

Conversion Between Different Measurement Systems

Different measurement systems have developed historically and remain in use across science, engineering, commerce and everyday life. Converting between SI, CGS, FPS, US customary and Imperial systems requires accurate conversion factors and careful identification of unit definitions. Particular attention is needed for units such as pounds, gallons, ounces and tons, which can have different meanings in different systems.

General

Q_target = Q_original × conversion factor

Speed

1 mi/h ≈ 0.44704 m/s

Force

1 lbf ≈ 4.448221615 N

Pressure

1 psi ≈ 6894.757293 Pa

Energy

1 ft·lbf ≈ 1.355817948 J

Historical CGS

  • 1 dyn = 10⁻⁵ N

  • 1 erg = 10⁻⁷ J

  • 1 P (poise) = 0.1 Pa·s

Explanation

The International System of Units is the internationally preferred coherent system for scientific measurement, but several other measurement systems remain in use. The CGS system is based on centimetre, gram and second. The FPS system is based on foot, pound and second. US customary and Imperial systems share some unit names but do not always share the same definitions. These systems arose from historical and practical requirements, and their units continue to appear in engineering drawings, older scientific literature, product specifications, construction, aviation and everyday commerce. Conversion between systems must begin with identification of the exact source unit. For example, the US liquid gallon and Imperial gallon are different volumes. A US liquid gallon is exactly 3.785411784 litres, while an Imperial gallon is exactly 4.54609 litres. The word gallon alone is therefore insufficient when precision matters. The pound also requires attention. The avoirdupois pound is a unit of mass, defined as exactly 0.45359237 kilogram. Pound-force (lbf) is a unit of force, not mass. In engineering, the distinction between pound-mass, pound-force and slug is important because mass and force are different physical quantities. The slug is a mass unit used in some FPS engineering contexts. The conversion factor between systems must preserve dimensions. A mass cannot be converted into a force without specifying an acceleration, and a force cannot be treated as a mass merely because both may be informally described using pounds. The factor-label method is suitable for these conversions. For example, miles per hour can be converted to metres per second by converting miles to metres and hours to seconds. Pressure may be converted from psi to pascals, and energy from foot-pounds to joules. Historical CGS units such as dyne and erg can be converted to SI units through their definitions: 1 dyn = 10⁻⁵ N and 1 erg = 10⁻⁷ J. Conversion should also account for whether the source quantity is absolute, gauge, mass-based or force-based. In technical work, the exact system and unit definition should be stated, and the final result should use a consistent system. SI units are generally preferred for scientific reporting because they provide a coherent international framework.

Variables

SymbolMeaningSi Unit

Q_original

Quantity expressed in the source measurement system

Source-system unit

Q_target

Same quantity expressed in the target system

Target-system unit

C

Conversion factor between the specified units

Dimensionless ratio for equivalent quantities

m

Mass

kg

F

Force

N

Example or application

A worked example has not yet been added.

Definition

Conversion between measurement systems is the process of expressing a physical quantity from one established unit system in another while preserving its physical value and dimensional meaning.

Purpose

To translate measurements between historically and regionally different unit systems without changing the physical quantity represented.

Importance

Cross-system conversion is necessary for international engineering, interpretation of historical data, scientific collaboration, manufacturing, construction, transportation and technical safety.

Measurement Systems

NameBasisCommon UnitsTypical Use

International System of Units (SI)

Metre, kilogram, second and other SI base units

  • m

  • kg

  • s

  • N

  • Pa

  • J

International science, engineering and most modern technical standards.

Centimetre-Gram-Second (CGS)

Centimetre, gram and second

  • cm

  • g

  • s

  • dyn

  • erg

Historical physics literature and some specialized scientific conventions.

Foot-Pound-Second (FPS)

Foot, pound-based mass or force conventions, and second

  • ft

  • lbm

  • lbf

  • s

  • slug

Some engineering and historical technical applications.

US customary system

Units historically used in the United States

  • inch

  • foot

  • yard

  • mile

  • US gallon

  • pound

US construction, product specifications, transport and everyday measurement.

Imperial system

British Imperial units

  • inch

  • foot

  • yard

  • mile

  • Imperial gallon

  • Imperial fluid ounce

Some UK contexts and historical measurements.

Important Conversion Factors

QuantityConversionStatus

Length

1 in = 0.0254 m

Exact

Length

1 ft = 0.3048 m

Exact

Length

1 yd = 0.9144 m

Exact

Length

1 mi = 1609.344 m

Exact for the international mile

Mass

1 lbm = 0.45359237 kg

Exact for the international avoirdupois pound

Force

1 lbf = 4.4482216152605 N approximately

Defined using the standard acceleration of gravity

Volume

1 US liquid gallon = 3.785411784 L

Exact

Volume

1 Imperial gallon = 4.54609 L

Exact

Pressure

1 psi ≈ 6894.757293 Pa

Defined conversion

Energy

1 ft·lbf ≈ 1.355817948 J

Defined conversion

Mass And Force Distinction

Mass

Mass measures inertia and is expressed in kilograms or pound-mass.

Force

Force is an interaction that can change motion and is expressed in newtons or pound-force.

Relationship

F = ma

Slug Definition

In the coherent FPS engineering convention, 1 slug is the mass accelerated at 1 ft/s² by a force of 1 lbf.

Warning

Pound-mass (lbm) and pound-force (lbf) are not interchangeable. The use of the word pound without context can create serious engineering errors.

Worked Examples

ProblemSolutionAnswer

Convert 60 miles per hour into metres per second.

60 mi/h × (1609.344 m/1 mi) × (1 h/3600 s) = 26.8224 m/s.

26.8224 m/s

Convert 25 pounds-mass into kilograms.

25 lbm × (0.45359237 kg/1 lbm) = 11.33980925 kg.

11.33980925 kg

Convert 30 psi into pascals.

30 psi × 6894.757293 Pa/psi ≈ 206842.72 Pa.

206842.72 Pa

Convert 12,000 dynes into newtons.

12,000 dyn × 10⁻⁵ N/dyn = 0.12 N.

0.12 N

Convert 5 Imperial gallons into litres.

5 × 4.54609 L = 22.73045 L.

22.73045 L

System Identification Rules

  • Identify whether the source is US customary, Imperial, CGS or another system.

  • Check whether the unit is a unit of mass, force, volume or another quantity.

  • Check whether the unit definition is international, historical or jurisdiction-specific.

  • Use a conversion factor that matches the exact source and target definitions.

  • State the target unit explicitly.

  • For engineering calculations, use a consistent system throughout the equation.

Common Mistakes

  • Confusing US gallons with Imperial gallons.

  • Confusing pound-mass with pound-force.

  • Treating mass and force as interchangeable.

  • Using an approximate conversion factor where exact precision is required.

  • Confusing historical and international definitions of a mile or other customary units.

  • Mixing CGS and SI units inside one equation without converting them.

  • Forgetting to convert time units in speed and rate calculations.

Limitations And Considerations

  • Some unit names have multiple definitions in different systems.

  • Historical data may use obsolete definitions that differ slightly from modern definitions.

  • A conversion factor cannot correct an incorrectly identified original unit.

  • Force and mass require dimensional distinction.

  • Engineering specifications may require a particular standard or rounding convention.

  • Some customary units are defined exactly, while measured physical quantities expressed in them still carry uncertainty.

Scientific Applications

  • International engineering and manufacturing.

  • Interpreting historical scientific experiments.

  • Converting vehicle speed and fuel-related measurements.

  • Construction and structural engineering.

  • Fluid pressure and mechanical force calculations.

  • Scientific comparison of CGS and SI literature.

Related Concepts

  • Unit conversion

  • Factor-label method

  • SI and CGS systems

  • Mass and force

  • Dimensional consistency

  • Standardized unit definitions

Reference

TitleOrganizationUrl

Guide for the Use of the International System of Units (SI), NIST SP 811

NIST

https://www.nist.gov/pml/special-publication-811

The International System of Units (SI Brochure), 9th edition

BIPM

https://www.bipm.org/en/publications/si-brochure

Related Topic

  • Fundamental Principles of Unit Conversion

  • Conversion Factors and Dimensional Factor-Label Method

  • Conversion of Derived, Compound and Complex Units

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.

Suggest a correction or source · More in Units & Measurement