A typical Vernier caliper consists of a graduated main scale, a sliding Vernier scale, external measuring jaws, internal measuring jaws, a depth rod or blade, a locking screw and sometimes a fine-adjustment mechanism. The external jaws measure outside dimensions such as thickness and diameter. The smaller upper jaws measure internal dimensions such as the inside diameter of a hole. The depth rod measures depths, while the step-measuring surfaces can measure step heights.
The Vernier principle is based on a small difference between the spacing of divisions on two scales. When one Vernier division is slightly shorter or longer than one main-scale division, the alignment of the divisions identifies a fractional part of a main-scale interval. In the common direct Vernier arrangement, the least count is the difference between one main-scale division and one Vernier-scale division.
Before measurement, clean the jaws and workpiece, close the instrument gently and check for zero error. Place the object correctly between the appropriate measuring surfaces. Avoid excessive force, tilting or measuring across burrs. Read the main-scale value immediately to the left of the Vernier zero, identify the Vernier division that aligns with a main-scale mark and add the corresponding Vernier contribution. Apply a zero correction if required.
Vernier calipers are available in metric and inch versions, with analogue, dial and digital displays. Their resolution and permissible error depend on the instrument design and specification.
Vernier Caliper: Principles, Construction and Measurement
A Vernier caliper is a precision instrument used to measure external dimensions, internal dimensions, depths and step heights. It uses the relative displacement of a main scale and a Vernier scale to obtain readings smaller than the smallest main-scale division.
Direct Vernier Least Count
LC = 1 MSD − 1 VSD
General Reading
Observed reading = Main-scale reading + (Coinciding Vernier division × LC)
Corrected Reading
Corrected reading = Observed reading + Zero correction
Zero Correction
Zero correction = − Zero error
Alternative
For a Vernier with n divisions equal to (n − 1) main-scale divisions, LC = 1 MSD/n.
Explanation
Variables
| Symbol | Meaning | Unit |
|---|---|---|
MSD | One main-scale division | mm or another scale unit |
VSD | One Vernier-scale division | mm or another scale unit |
LC | Least count | mm or another scale unit |
n | Number of Vernier divisions in the stated construction | Dimensionless |
Example or application
A worked example has not yet been added.
Definition
Vernier Caliper
A sliding measuring instrument that uses a Vernier scale to measure dimensions with finer resolution than the main scale.
Main Scale
The fixed graduated scale on the body of the instrument.
Vernier Scale
The graduated scale attached to the movable slider.
Least Count
The smallest measurement increment that can be read using the scale arrangement.
Zero Error
A non-zero indication when the measuring surfaces are brought together under the specified zero-check condition.
Purpose
To measure external and internal dimensions, depths and step heights with finer resolution than an ordinary graduated ruler.
Importance
Vernier calipers are widely used in mechanical workshops, engineering laboratories, manufacturing inspection and educational experiments because one instrument can perform several dimensional measurements.
Construction
Main Scale
A fixed graduated beam carrying the principal scale markings.
Sliding Jaw
A movable assembly that carries the Vernier scale and one set of measuring jaws.
External Jaws
Opposing lower jaws used to measure outside dimensions.
Internal Jaws
Smaller upper jaws used to measure inside dimensions.
Depth Rod
A projecting rod used to measure the depth of holes, slots or recesses.
Locking Screw
Holds the slider in position after setting or measuring.
Fine Adjustment
A mechanism on some models that allows controlled, small movement of the slider.
Measurement Principle
Main Scale Division
The value represented by the spacing between adjacent main-scale marks.
Vernier Division
The value represented by the spacing between adjacent Vernier marks.
Coincidence
The Vernier division that aligns most closely with a main-scale mark identifies the fractional scale contribution.
Least Count
The difference between the values of one main-scale division and one Vernier-scale division in a direct Vernier.
Measurement Procedure
Identify the instrument's scale system, units and least count.
Clean the measuring faces and the workpiece.
Close the jaws gently and check whether the zero marks coincide.
Determine and record any zero error.
Select the correct measuring surfaces for the dimension being measured.
Position the object without tilting or forcing the jaws.
Apply gentle, consistent contact pressure.
Read the main-scale value immediately to the left of the Vernier zero.
Find the Vernier division that coincides with a main-scale mark.
Multiply its division number by the least count.
Add the main-scale and Vernier contributions.
Apply the zero correction and record the corrected value with its unit.
Repeat the measurement at suitable positions when the object's geometry or variation requires it.
Zero Error
Positive Zero Error
If the Vernier zero lies to the right of the main-scale zero when the jaws are closed, the instrument has positive zero error under the usual direct Vernier convention.
Negative Zero Error
If the Vernier zero lies to the left of the main-scale zero when the jaws are closed, the instrument has negative zero error.
Correction Rule
Zero correction has the opposite sign to zero error.
Caution
The exact reading and correction procedure must follow the instrument's scale arrangement and manufacturer instructions.
Worked Examples
| Problem | Solution |
|---|---|
A Vernier caliper has 1 MSD = 1 mm and 10 VSD = 9 mm. The main-scale reading is 24 mm and the 6th Vernier division coincides. Find the observed reading. | One VSD = 9/10 mm = 0.9 mm. LC = 1.0 − 0.9 = 0.1 mm. Vernier contribution = 6 × 0.1 = 0.6 mm. Observed reading = 24 + 0.6 = 24.6 mm. |
The observed reading is 18.42 mm and the zero error is +0.03 mm. Find the corrected reading. | Zero correction = −0.03 mm. Corrected reading = 18.42 − 0.03 = 18.39 mm. |
A caliper has a least count of 0.02 mm. Its main-scale reading is 32 mm and the 7th Vernier division coincides. Find the reading before zero correction. | Vernier contribution = 7 × 0.02 = 0.14 mm. Observed reading = 32 + 0.14 = 32.14 mm. |
Measurement Precautions
Do not force the jaws against the object.
Keep the measuring faces clean and free from oil, dust and chips.
Avoid parallax when reading analogue scales.
Check zero error before use.
Measure a cylindrical object at suitable orientations if diameter variation is possible.
Use the correct jaws for internal and external measurements.
Do not use a damaged or loose slider.
Avoid measuring hot objects unless the instrument and procedure are designed for that condition.
Advantages
Can measure external dimensions, internal dimensions and depths.
Available in different ranges and resolutions.
More versatile than a simple ruler.
Analogue versions do not require batteries.
Digital versions can provide convenient direct readings and data output.
Limitations
Reading analogue Vernier scales requires care and practice.
Measurement accuracy depends on jaw condition, alignment and applied force.
Small objects may be difficult to position correctly.
Wear, dirt and mechanical play can affect results.
A caliper is not always suitable for the tightest dimensional tolerances; a suitable micrometer or specialized instrument may be required.
Common Mistakes
Forgetting to check zero error.
Using the wrong Vernier division or least count.
Reading the scale from an angle.
Applying excessive force.
Using internal jaws to measure an external dimension or vice versa.
Reporting the instrument's least count as its guaranteed accuracy.
Applications
Measuring shaft and rod diameters
Measuring the thickness of plates and components
Measuring internal hole diameters
Measuring depths of holes and recesses
Manufacturing and workshop inspection
Physics and engineering laboratory experiments
Reference
JCGM 200, International Vocabulary of Metrology (VIM).
NIST, Special Publication 811, Guide for the Use of the International System of Units (SI).
Manufacturer technical manuals for the specific Vernier caliper design.
Related Topic
Micrometer Screw Gauge: Principles and Measurement
Resolution, Sensitivity, Range and Threshold of Instruments
Measurement of Length, Distance, Area and Volume
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.
Suggest a correction or source · More in Units & Measurement