✦ScienexySCIENCE KNOWLEDGE LIBRARY
reference · SCI-REF-003-069

Electrical Measurement Instruments and Sensors

Electrical measurement instruments determine quantities such as voltage, current, resistance, power, energy, frequency, capacitance and magnetic-field-related electrical properties. They use analogue and digital circuits, electromagnetic effects, resistance networks, current shunts, voltage dividers and electronic sensors.

Ohms Law

V = IR

Electrical Power DC

P = VI

Resistive Power

P = I²R = V²/R

Electrical Energy

E = Pt

Series Resistance

R_total = R₁ + R₂ + ... + Rₙ

Parallel Resistance

1/R_total = 1/R₁ + 1/R₂ + ... + 1/Rₙ

Shunt Current

I = V_shunt/R_shunt

Note

The simple power equations apply directly to suitable DC or purely resistive conditions. AC power measurement may require power factor and waveform considerations.

Explanation

Electrical quantities are measured using instruments designed for specific circuit conditions. A voltmeter measures potential difference and is connected in parallel with the relevant circuit element. An ammeter measures current and is connected in series, or uses a current sensor such as a shunt or current transformer. An ohmmeter measures resistance and generally requires the circuit to be de-energized and isolated according to safe practice.

A digital multimeter combines several measurement functions, commonly voltage, current and resistance, and may also measure continuity, capacitance, frequency or temperature. An oscilloscope displays voltage as a function of time and is used to study waveforms, transients and timing. A wattmeter measures electrical power, while an energy meter integrates power over time.

Instrument loading must be considered. An ideal voltmeter has infinite input resistance, while a practical voltmeter has a high but finite input resistance. An ideal ammeter has zero resistance, while a practical ammeter has a small but nonzero burden voltage. Incorrect connection or unsuitable range selection can produce inaccurate readings or damage equipment.

Electrical measurements can be affected by frequency response, bandwidth, common-mode voltage, grounding, electromagnetic interference, lead resistance, contact resistance, waveform distortion and instrument safety category. High-energy circuits require appropriately rated equipment and trained handling.

Variables

SymbolMeaningUnit

V

Potential difference

V

I

Electric current

A

R

Electrical resistance

Ω

P

Electrical power

W

E

Electrical energy

J or kWh

t

Time

s or h

Example or application

A worked example has not yet been added.

Definition

Voltmeter

An instrument used to measure potential difference between two points.

Ammeter

An instrument used to measure electric current through a circuit.

Ohmmeter

An instrument used to determine electrical resistance.

Multimeter

An instrument that combines several electrical measurement functions.

Wattmeter

An instrument used to measure electrical power.

Energy Meter

An instrument that measures electrical energy transferred over time.

Oscilloscope

An instrument that displays an electrical signal as a function of time.

Transducer

A device that converts a physical quantity into an electrical signal or converts an electrical signal into another form.

Purpose

To evaluate electrical circuits, verify component specifications, monitor electrical systems, diagnose faults and determine the electrical performance of devices and installations.

Importance

Electrical measurement is essential for electronics, electrical power engineering, telecommunications, industrial automation, energy management, product testing and electrical safety.

Instrument Types

Analogue Voltmeter

Uses a moving-coil or other analogue mechanism to indicate voltage.

Digital Voltmeter

Uses signal conditioning and analogue-to-digital conversion to display voltage numerically.

Ammeter

Measures current using a shunt, moving-coil mechanism, current transformer or electronic sensor.

Ohmmeter

Applies a known test signal and determines resistance from the resulting electrical response.

Digital Multimeter

Combines multiple electrical measurement functions in one instrument.

Oscilloscope

Displays time-varying electrical signals and supports waveform analysis.

Wattmeter

Measures electrical power using voltage and current information with appropriate phase or waveform processing.

Energy Meter

Measures accumulated electrical energy, commonly in kilowatt-hours.

LCRMeter

Measures inductance, capacitance and resistance using specified test frequencies and signal conditions.

Clamp Meter

Measures current using a magnetic sensing arrangement without opening the conductor circuit, within its rated application.

Measurement Principles

Moving Coil

A current-carrying coil experiences torque in a magnetic field, producing pointer movement.

Shunt Method

A small known resistance produces a voltage proportional to current.

Voltage Divider

A known resistor network scales voltage to a suitable measurement range.

Electromagnetic Induction

Changing magnetic flux produces an induced voltage in a coil.

Current Transformer

Uses magnetic coupling to produce a scaled secondary current related to the primary current.

Analogue To Digital Conversion

Converts a conditioned analogue signal into a digital code for processing and display.

Connection Rules

Voltmeter

Connect in parallel across the element or points whose potential difference is required.

Ammeter

Connect in series with the branch whose current is required, using the appropriate current input and range.

Ohmmeter

Measure only under conditions specified by the instrument manufacturer; the circuit generally must be de-energized and isolated.

Oscilloscope

Use probes, grounding and voltage ratings appropriate to the circuit. Never assume a standard probe ground is isolated from protective earth.

Wattmeter

Connect voltage and current measurement paths according to the instrument's wiring diagram and phase requirements.

Measurement Procedure

  • Identify the electrical quantity and expected value.

  • Select an instrument with suitable range, accuracy, bandwidth and safety rating.

  • Inspect leads, probes, insulation and connectors.

  • Check calibration status and instrument condition.

  • Use the correct measurement function and input terminals.

  • De-energize and isolate circuits when required by the measurement method.

  • Make connections according to the instrument manual and applicable safety procedure.

  • Avoid exceeding voltage, current, power or category ratings.

  • Allow the reading to stabilize and record the value with its unit.

  • Disconnect safely and return the instrument to an appropriate storage condition.

Worked Examples

ProblemSolution

A resistor of 100 Ω carries a current of 0.20 A. Find the voltage across it.

V = IR = 0.20 × 100 = 20 V.

A DC circuit operates at 12 V and draws 2.0 A. Find the electrical power.

P = VI = 12 × 2.0 = 24 W.

A device uses 100 W for 5 h. Find the energy consumed in kilowatt-hours.

E = 100 W × 5 h = 500 Wh = 0.5 kWh.

Ac Measurement

Rms

Root-mean-square value represents the effective value of an alternating quantity for specified applications.

Frequency

The number of cycles per second, measured in hertz.

Power Factor

For sinusoidal steady-state conditions, power factor is cos φ, where φ is the phase angle between voltage and current.

Real Power

For sinusoidal steady-state conditions, P = V_rms I_rms cos φ.

Apparent Power

S = V_rms I_rms, measured in volt-amperes.

Caution

Non-sinusoidal waveforms may require true-RMS instruments and more complete power analysis.

Safety And Limitations

Overvoltage

Exceeding an instrument's voltage rating can damage the instrument and create a hazard.

Overcurrent

Incorrect current measurement connections can cause excessive current through the instrument.

Grounding

Oscilloscope grounding and common-mode limitations must be understood before connecting probes.

Bandwidth

An instrument may not accurately measure signals beyond its specified bandwidth.

Loading

Finite input impedance can alter the circuit being measured.

Interference

Electromagnetic interference and poor lead routing can introduce unwanted signals.

Measurement Category

Electrical instruments may have installation-category ratings describing transient overvoltage environments. The correct category and voltage rating must be selected for the application.

Common Mistakes

  • Connecting an ammeter in parallel across a voltage source.

  • Measuring resistance in an energized circuit.

  • Using an input terminal or range unsuitable for the measurement.

  • Ignoring the input resistance of a voltmeter.

  • Assuming ordinary average-responding meters measure all distorted AC waveforms accurately.

  • Ignoring oscilloscope grounding and common-mode constraints.

Applications

  • Electronic circuit testing

  • Electrical power systems

  • Industrial control panels

  • Battery and energy-system testing

  • Telecommunications

  • Electrical equipment maintenance

  • Research and calibration laboratories

Reference

  • IEC 61010 series, Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use.

  • NIST, Special Publication 811, Guide for the Use of the International System of Units (SI).

  • JCGM 200, International Vocabulary of Metrology (VIM).

Related Topic

  • Derived Units in Electricity and Magnetism

  • Advanced Electronic, Digital and Automated Measurement Systems

  • Measuring Instrument Characteristics and Performance Parameters

  • Time, Frequency and Period Measurement Instruments

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.

Suggest a correction or source · More in Units & Measurement