✦ScienexySCIENCE KNOWLEDGE LIBRARY
reference · SCI-REF-003-092

Measurement Standards and International Reference Systems

Measurement standards and international reference systems establish common, stable and scientifically defined references for expressing and comparing measurement results. They provide the foundation for the International System of Units, national measurement systems, calibration chains and worldwide measurement comparability.

A quantity Q can be expressed as Q = {Q} × [Q], where {Q} is its numerical value and [Q] is the corresponding measurement unit. Measurement standards provide reference values for realizing or comparing such quantities.

Explanation

A measurement standard provides a reference for assigning values to quantities. Standards allow measurements performed at different times and locations to be compared using a common measurement framework. Historically, many standards were based on physical artifacts, such as specially manufactured reference objects. Modern metrology increasingly realizes units through fixed values of fundamental constants of nature. The International System of Units, known as the SI, is the globally accepted system of measurement units. It defines seven base units: second, metre, kilogram, ampere, kelvin, mole and candela. Since the 2019 revision, all seven SI base units are defined by fixing numerical values of specified defining constants. These include the speed of light in vacuum, the caesium-133 hyperfine transition frequency, the Planck constant, the elementary charge, the Boltzmann constant, the Avogadro constant and the luminous efficacy of monochromatic radiation of frequency 540 × 10¹² Hz. A unit realization is the practical implementation of a unit definition using a suitable experiment or measurement system. Primary standards realize units at the highest available level without reference to another standard of the same quantity. Secondary standards obtain their values through calibration against higher-level standards. Working standards are used routinely in laboratories and industry. International comparison systems ensure that national standards remain consistent. The CIPM Mutual Recognition Arrangement provides a framework for recognizing national measurement standards and calibration and measurement capabilities among participating institutes. Measurement standards may be physical, chemical, biological, electrical, dimensional, time-frequency or computational in nature. The selection of a reference depends on the measurand, required uncertainty and application.

Variables

SymbolMeaningSi Unit

Q

Physical quantity

The applicable SI unit

{Q}

Numerical value of the quantity

Dimensionless

[Q]

Measurement unit of the quantity

Relevant SI or accepted unit

Example or application

A worked example has not yet been added.

Definition

A measurement standard is a realization of the definition of a given quantity, with a stated quantity value and associated measurement uncertainty, used as a reference.

Purpose

To establish common measurement references and ensure that measurement results can be compared consistently across laboratories, industries and countries.

Importance

International measurement standards support scientific reproducibility, instrument calibration, industrial quality, international trade, regulatory compliance and technological development.

International System Of Units

Name

International System of Units

Abbreviation

SI

Description

The internationally agreed system of measurement units maintained through the international metrology framework.

Base Units

QuantityUnitSymbolDefining Constant

Time

second

s

Caesium-133 hyperfine transition frequency, ΔνCs = 9 192 631 770 Hz.

Length

metre

m

Speed of light in vacuum, c = 299 792 458 m/s.

Mass

kilogram

kg

Planck constant, h = 6.626 070 15 × 10⁻³⁴ J s.

Electric current

ampere

A

Elementary charge, e = 1.602 176 634 × 10⁻¹⁹ C.

Thermodynamic temperature

kelvin

K

Boltzmann constant, k = 1.380 649 × 10⁻²³ J/K.

Amount of substance

mole

mol

Avogadro constant, Nₐ = 6.022 140 76 × 10²³ mol⁻¹.

Luminous intensity

candela

cd

Luminous efficacy Kcd = 683 lm/W for monochromatic radiation of frequency 540 × 10¹² Hz.

Classification Of Measurement Standards

LevelDescriptionExamples

International standards and references

References and international arrangements that support global consistency and comparison of national measurement standards.

  • SI definitions

  • International comparisons

  • International reference systems

Primary measurement standards

Standards that realize or establish quantity values at the highest level for a particular measurement field.

  • Primary frequency standards

  • Primary electrical standards

  • Primary mass realization

Secondary standards

Standards whose values are established through calibration against primary standards or higher-level references.

  • Secondary electrical standards

  • Secondary pressure standards

Reference standards

Standards maintained for calibration or verification within an organization or laboratory.

  • Laboratory reference weights

  • Reference thermometers

Working standards

Standards used routinely to calibrate or verify instruments during normal operations.

  • Working gauge blocks

  • Routine reference masses

Transfer standards

Standards used to transfer measurement values between locations or systems.

  • Portable reference devices

  • Transportable comparison standards

Physical And Fundamental References

Artifact Based Standards

Physical objects maintained with controlled conditions and characterized values. Their stability, handling and environmental sensitivity must be managed.

Constant Based Standards

Standards realized through fixed defining constants of nature and suitable experimental procedures.

Reference Systems

Agreed systems of units, coordinate frames, time scales, reference data and realization procedures that provide common measurement references.

International Measurement Framework

BIPM

Coordinates international metrology and supports the consistency of the SI.

CGPM

The General Conference on Weights and Measures is the international body that makes major decisions concerning the SI and the international measurement system.

CIPM

The International Committee for Weights and Measures oversees international metrological cooperation and implementation.

CIPM MRA

The Mutual Recognition Arrangement provides a framework for recognizing national measurement standards and calibration and measurement capabilities.

Key Objective

To promote worldwide comparability and confidence in national measurement standards and calibration services.

Realization And Dissemination

  • An internationally defined unit is realized through a suitable primary method or measurement system.

  • National metrology institutes maintain national measurement standards.

  • National standards are compared with international references or other national standards where appropriate.

  • Calibration services transfer measurement values to reference and working standards.

  • Industrial and testing laboratories use calibrated instruments to perform routine measurements.

  • Traceability and uncertainty information accompany the transfer of measurement values.

Worked Example

Problem

A laboratory uses a working mass standard to verify a balance. The working standard was calibrated against a reference standard, which is traceable to a national mass standard.

Measurement Reference

The mass value assigned to the working standard.

Calibration Path

Working standard → reference standard → national measurement standard → internationally consistent SI realization.

Interpretation

The laboratory can relate its balance measurements to a recognized measurement reference through documented calibrations and associated uncertainties.

Important Distinctions

  • A unit definition is not the same as a particular instrument that realizes the unit.

  • A primary standard is not automatically uncertainty-free.

  • A national standard is maintained by a national metrology system; it is not necessarily a physical artifact.

  • International recognition depends on appropriate comparisons, quality systems and demonstrated capabilities.

  • Traceability is a property of a measurement result, not simply a label attached to an instrument.

Applications

  • National measurement systems

  • International calibration

  • Scientific research

  • Industrial measurement

  • Global trade

  • Reference-standard maintenance

Reference

  • BIPM, The International System of Units (SI Brochure), 9th edition.

  • BIPM, International Committee for Weights and Measures Mutual Recognition Arrangement (CIPM MRA).

  • JCGM 200, International Vocabulary of Metrology (VIM).

Related Topic

  • SCI-REF-003-091

  • SCI-REF-003-093

  • SCI-REF-003-094

  • SCI-REF-003-095

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.

Suggest a correction or source · More in Units & Measurement