✦ScienexySCIENCE KNOWLEDGE LIBRARY
reference · SCI-REF-006-094

Electrical Engineering: Circuit and Component Symbols

Electrical engineering notation represents electrical quantities, circuit components, power sources, loads, connections, protection devices, and system behavior. Circuit diagrams use standardized graphical symbols and reference designators to describe how electrical components are connected and how electrical energy is transferred or controlled.

Ohm's law: V = IR. Electrical power: P = VI = I²R = V²/R for a resistive element under the applicable operating conditions. Kirchhoff's current law: ∑Iₖ = 0 at a node using consistent signed reference directions. Kirchhoff's voltage law: ∑Vₖ = 0 around a closed loop. Capacitive impedance: Z_C = 1/(jωC). Inductive impedance: Z_L = jωL.

Explanation

Electrical circuit notation combines component symbols, connection lines, reference designators, polarity marks, terminal identifiers, and mathematical quantities. A circuit diagram is a functional representation of electrical connections and is not necessarily a physical layout. Common passive components include resistors, capacitors, and inductors. Sources include independent voltage sources, current sources, and dependent sources. Switching and protection components include switches, relays, fuses, circuit breakers, and protective earth connections. Semiconductor devices such as diodes and transistors are also used in electrical and electronic diagrams, although their detailed operation is commonly studied in electronics. Circuit quantities include voltage, current, resistance, conductance, capacitance, inductance, impedance, power, and energy. Voltage is defined between two points, while current is associated with a chosen reference direction through a branch. Conventional current direction is defined as the direction of positive charge flow, opposite to electron drift in a typical metallic conductor. Kirchhoff's current law expresses conservation of electric charge at a node, and Kirchhoff's voltage law expresses conservation of energy around a closed loop. Series and parallel connections have different equivalent-resistance relationships. Alternating-current circuits require phasor and complex-impedance notation. Circuit diagrams may use ground symbols to establish a reference potential, but different ground symbols can represent protective earth, chassis ground, or signal reference. Their meanings must be checked in the schematic.

Variables

SymbolMeaningUnit

V

Voltage or electric potential difference.

V

I

Electric current.

A

R

Electrical resistance.

Ω

G

Electrical conductance.

S

C

Capacitance.

F

L

Inductance.

H

Z

Complex impedance.

Ω

P

Electrical power.

W

E

Electrical energy or electromotive force, depending on context.

J or V, respectively.

ω

Angular frequency.

rad·s⁻¹

j

Imaginary unit used in electrical engineering notation, with j² = −1.

Dimensionless

Example or application

A worked example has not yet been added.

Definition

Electrical engineering symbols are standardized graphical and mathematical representations of electrical quantities, circuit components, connections, sources, loads, and electrical-system relationships.

Purpose

To describe electrical circuits and systems in a consistent way that supports circuit design, analysis, installation, troubleshooting, testing, and maintenance.

Importance

Standard electrical symbols make circuit diagrams readable across engineering teams and manufacturers. Correct notation is essential for understanding polarity, connection topology, protective devices, electrical ratings, and fault-current paths. It also helps prevent wiring mistakes and supports compliance with electrical safety standards.

Passive Component Symbols

ComponentCommon RepresentationReference DesignatorFunction

Resistor

A rectangular IEC-style symbol or a zigzag ANSI-style symbol.

R

Opposes current flow and dissipates electrical energy as heat.

Capacitor

Two parallel plates; polarized types may include a polarity mark.

C

Stores energy in an electric field.

Inductor

A coil or series of curved loops.

L

Stores energy in a magnetic field.

Transformer

Two or more coupled winding symbols, often with a core indication.

T

Transfers electrical energy through electromagnetic induction.

Lamp

A circle containing a cross or another standard lamp mark.

L or a project-specific identifier.

Converts electrical energy into light and heat.

Fuse

A standardized series protective-device symbol.

F

Interrupts a circuit when excessive current causes its element to operate.

Source And Switching Symbols

ComponentRepresentationFunction

Independent voltage source

A source symbol marked with positive and negative polarity or an equivalent standardized form.

Maintains a specified voltage under its idealized model.

Independent current source

A circular source symbol with a current-direction arrow.

Maintains a specified current under its idealized model.

Switch

A break or movable contact in a circuit line.

Opens or closes an electrical path.

Relay

A coil and associated contact representation.

Uses an electrically controlled mechanism to change contact states.

Circuit breaker

A standardized protective switching-device symbol.

Opens a circuit under specified fault or overload conditions.

Protective earth

A standardized earth or protective-earth mark.

Identifies a protective connection intended to reduce electric-shock risk.

Connection And Reference Notation

SymbolMeaning

Node

An electrically connected junction shared by circuit branches.

Junction dot

A filled dot commonly indicates an electrical connection between intersecting conductors.

Crossing without junction

A crossing line without a connection mark may indicate that conductors are not electrically connected, depending on the drafting convention.

GND

A circuit reference potential, often called ground; its physical implementation must be defined.

PE

Protective earth.

N

Neutral conductor in applicable power-distribution systems.

L

Line or live conductor in applicable power-distribution systems.

R1, C1, L1

Example reference designators identifying individual components.

ACAnd Phasor Notation

SymbolMeaningUnit

f

Frequency of an alternating electrical quantity.

Hz

ω

Angular frequency, related to frequency by ω = 2πf.

rad·s⁻¹

φ

Phase angle.

rad or degree

Z

Complex impedance, Z = R + jX for a simple series representation.

Ω

X

Reactance.

Ω

S

Complex apparent power, commonly written S = P + jQ.

VA

P

Active or real power.

W

Q

Reactive power in AC power notation.

var

Worked Examples

ExampleGivenCalculationResult

Ohm's law

A 10 Ω resistor is connected across a 12 V ideal DC source.

I = V/R = 12/10

Current = 1.2 A.

Resistor power

A 10 Ω resistor carries a current of 1.2 A.

P = I²R = 1.2² × 10

Power dissipation = 14.4 W.

Series resistance

Three resistors of 10 Ω, 20 Ω, and 30 Ω are connected in series.

Rₑq = 10 + 20 + 30

Equivalent resistance = 60 Ω.

Parallel resistance

Two resistors of 6 Ω and 3 Ω are connected in parallel.

1/Rₑq = 1/6 + 1/3

Equivalent resistance = 2 Ω.

Common Misinterpretations

MisinterpretationCorrection

Assuming every ground symbol means a direct connection to protective earth.

Distinguish circuit reference ground, chassis ground, and protective earth according to the schematic.

Treating a line crossing as an electrical junction.

Check the junction dot and the drawing convention.

Confusing conventional current direction with electron drift direction.

Conventional current is defined in the direction positive charge would move.

Using a resistor symbol to infer its physical mounting or exact dimensions.

Use the circuit diagram for electrical connectivity and the physical layout or component specification for construction details.

Reference

  • IEC 60617: Graphical Symbols for Diagrams

  • IEC 61082 series: Preparation of Documents Used in Electrotechnology

  • IEC 60027 series: Letter Symbols to Be Used in Electrical Technology

  • Alexander and Sadiku, Fundamentals of Electric Circuits

  • Nilsson and Riedel, Electric Circuits

Related Topic

  • SCI-REF-006-091

  • SCI-REF-006-095

  • SCI-REF-006-100

Sources and verification

Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.

  • Source verification pending; check an authoritative textbook, university, standards body, or peer-reviewed source.

Suggest a correction or source · More in Scientific Symbols & Notation