Pressure and stress are both expressed as force divided by area, so they share the same dimensional unit: N·m⁻², called the pascal (Pa). However, pressure usually describes an external normal force acting on a surface, especially in fluids and gases, whereas stress describes internal force intensity within a solid material. Normal stress acts perpendicular to a cross-section, while shear stress acts parallel to it. A pressure or stress value can be converted between Pa, kPa, MPa, bar, atm, mmHg, Torr, and psi without changing the physical quantity. Before calculating, convert all force and area values into compatible units. For example, if force is in newtons and area is in square millimetres, convert the area into square metres or use the equivalent relationship 1 N/mm² = 1 MPa. Also distinguish absolute pressure from gauge pressure. Absolute pressure is measured relative to a perfect vacuum, while gauge pressure is measured relative to the local ambient pressure. Their relationship is P_absolute = P_gauge + P_ambient. Stress calculations may require identifying the correct cross-sectional area and distinguishing normal from shear loading.
Pressure and Stress: Unit Equivalence and Practical Problems
Learn why pressure and stress share the same units and apply their conversion relationships in practical calculations.
p = F/A; σ = F/A; τ = Fₜ/A; P_absolute = P_gauge + P_ambient
Explanation
Variables
P
Pressure.
Σ
Normal stress.
Τ
Shear stress.
F
Normal force.
Fₜ
Tangential force.
A
Area over which the force acts.
P absolute
Absolute pressure.
P gauge
Gauge pressure.
P ambient
Ambient pressure.
Example or application
Problem
A material experiences a compressive force of 20,000 N over a cross-sectional area of 0.01 m². Calculate the compressive stress in Pa and MPa.
Solution
Stress = F/A = 20,000/0.01 = 2,000,000 Pa. Since 1 MPa = 1,000,000 Pa, stress = 2 MPa.
Answer
2,000,000 Pa = 2 MPa
Definition
Pressure and stress are quantities measured as force per unit area, with the pascal as their common SI unit.
Key Unit Equivalences
| Relationship | Equivalent |
|---|---|
1 Pa | 1 N·m⁻² |
1 kPa | 1000 Pa |
1 MPa | 1,000,000 Pa |
1 bar | 100,000 Pa |
1 atm | 101,325 Pa |
1 Torr | 101,325/760 Pa |
1 psi | Approximately 6894.757293 Pa |
1 N/mm² | 1 MPa |
Problem Solving Method
Identify whether the quantity is pressure, normal stress, or shear stress.
Write down the applied force and the relevant area.
Convert force and area into compatible units.
Calculate force divided by area.
Convert the resulting Pa value into the required pressure or stress unit.
For fluid pressure, determine whether the value is absolute, gauge, or differential pressure.
Check dimensional consistency and round the final answer appropriately.
Purpose
To connect force-per-area calculations with pressure and stress unit conversions.
Importance
These relationships are central to structural design, material testing, fluid systems, pressure vessels, hydraulics, and engineering safety calculations.
Practice Problems
| Question | Answer |
|---|---|
Convert 450 kPa into Pa. | 450,000 Pa |
Convert 5 MPa into kPa. | 5000 kPa |
Convert 2.5 bar into Pa. | 250,000 Pa |
Convert 1.5 atm into Pa. | 151,987.5 Pa |
A force of 500 N acts normally on an area of 0.025 m². Calculate the pressure. | 20,000 Pa or 20 kPa |
Convert 100 psi into kPa. | Approximately 689.476 kPa |
Common Mistakes
Confusing pressure with force.
Using the wrong area or failing to square a length conversion when converting area units.
Confusing normal stress with shear stress.
Treating bar and standard atmosphere as identical.
Treating torr and mmHg as exactly identical without checking their definitions.
Confusing absolute pressure with gauge pressure.
Mixing newtons with an area expressed in incompatible units.
Reporting stress in MPa when the calculation actually produced Pa without converting.
Sources and verification
Sources are shown as provided in the project data. Not every source has yet been independently verified. Please report errors or missing citations.
- BIPM - The International System of Units (SI Brochure)
- NIST - Guide to the SI
- OpenStax - University Physics, Volume 1
- OpenStax - University Physics, Volume 2
Suggest a correction or source · More in Conversions & Equivalences